Heavy Lift Hexa Build

I did it, finally the hexa is ready for a tune! its taken its sweet time, over 2 months of waiting and building and lots of $$$ but im excited to take it for its maiden flight real soon. my intention of using this hexa was for aerial video with future heavy lift if and when needed.

any help with tuning would be helpful. will try and get some video of the maiden flight and some tuning progress vids too.

hexa1.jpg

hexa3.jpg

hexa5.jpg

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Right now tuning Hexa jdrones 2.5.3 880, 12x4.5, Started off with stock pids and Rate Roll P 0.1, Stabilize Roll P 3, TriM_throttle 450. You people way ahead with the same rig, any final tuning parameter values?

  • holy cow!

    fixed it. all this time it was in mission planner setting up the radio properly! arrggg. i didnt know the software was so particular when it asks after calibrating radio " center all sticks", previously i just had the throttle stick to 0 then click ok. 

    ok so back on track... yay.. off to tune, will do some flight/tune vids too. over and out

  • @Paul, have you tried disconnecting each individual esc and calibrating? BTW, your hexa looks nice. I finally put mine together too, so I was looking for some tuning help. Are you using a UAP1 frame from Rusty? I have the same.

    @nicolas, do you fly at all in acro/rate mode? i have just finally finished building my hexa and tried the default PIDs and it was very wobbly. I will try out your shared settings as starting point. My hexa is heavy...almost 2.5kg AUW.

  • I've searched high and low, still no luck. Ivwould like to get some tuning soon as ive got a small video job coming up but im dead in water right now. Is there something wrong with .55 or is this hardware related?
  • and to the apm board3692313298?profile=original

  • this is the pcb connections
    3692312791?profile=original

  • hey guys, here is a quick video what is going on with my esc/motors. any one can help?

    https://www.youtube.com/watch?v=HeP-e9DJFz0

  • hi guys, any one have any clue as to why my esc/motors are beeping like crazy after a firmware update .55 ?

  • thanks, ill give it a shot, hopefully tomorrow if the weather holds out.

  • Hi, nice hexa. Tuning is a bit tricky. Some of us (for example me) are having to fine tune hexa. Is quite dificult. But you can start with some values like: 

    stab P: around 1.8 - 2.5 (powerful motors)

    stab I: 0.1

    rate P: 0.080 - 0.120 (again powerful motors)

    These are actually mines:

    STB_PIT_P  3 (I think I change it last flight to 2.4 but I'm not sure, it flies with 3, but little wobble)

    STB_PIT_I    0.1

    STB_PIT_IMAX  30


    RATE_PIT_P             0.085

    RATE_PIT_I              0.1
    RATE_PIT_IMAX       15

    I'm using 2.0.54 firmware with the attitude patch.

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @a1k0n: @SmallpixelCar @diyrobocars It's just something that's easy to track with chroma keying. I ended up using different colors on th…
5 hours ago
DIY Robocars via Twitter
5 hours ago
DIY Robocars via Twitter
RT @TinkerGen_: "The Tinkergen MARK ($199) is my new favorite starter robocar. It’s got everything — computer vision, deep learning, sensor…
Nov 23
DIY Robocars via Twitter
Nov 23
DIY Robocars via Twitter
RT @roboton_io: Join our FREE Sumo Competition 🤖🏆 👉 https://roboton.io/ranking/vsc2020 #sumo #robot #edtech #competition #games4ed https://t.co/WOx…
Nov 16
DIY Drones via Twitter
First impressions of Tinkergen MARK robocar https://ift.tt/36IeZHc
Nov 16
DIY Robocars via Twitter
Our review of the @TinkerGen_ MARK robocar, which is the best on the market right now https://diyrobocars.com/2020/11/15/first-impressions-of-tinkergen-mark-robocar/ https://t.co/ENIlU5SfZ2
Nov 15
DIY Robocars via Twitter
RT @Ingmar_Stapel: I have now explained the OpenBot project in great detail on my blog with 12 articles step by step. I hope you enjoy read…
Nov 15
DIY Robocars via Twitter
RT @DAVGtech: This is a must attend. Click the link, follow link to read the story, sign up. #chaos2020 #digitalconnection #digitalworld ht…
Nov 15
DIY Robocars via Twitter
RT @a1k0n: Got a new chassis for outdoor races (hobbyking Quantum Vandal) but I totally didn't expect that it might cause problems for my g…
Nov 11
DIY Drones via Twitter
First impressions of the Intel OpenBot https://ift.tt/36qkVV4
Nov 10
DIY Robocars via Twitter
Nov 9
DIY Robocars via Twitter
Excellent use of cardboard instead of 3D printing! https://twitter.com/Ingmar_Stapel/status/1324960595318333441
Nov 7
DIY Robocars via Twitter
RT @chr1sa: We've got a record 50 teams competing in this month's @DIYRobocars @donkey_car virtual AI car race. Starting today at 10:00am…
Nov 7
DIY Robocars via Twitter
Nov 6
DIY Robocars via Twitter
RT @a1k0n: Car's view, using a fisheye camera. The ceiling light tracking algorithm gave me some ideas to improve ConeSLAM, and having grou…
Nov 5
More…