Replies

  • Moderator

    Here's all of them, I'll put them in the wiki:

     CH6_NONE 0
    // Attitude
     CH6_STABILIZE_KP 1
     CH6_STABILIZE_KI 2
     CH6_STABILIZE_KD 29        // duplicate with CH6_DAMP
     CH6_YAW_KP 3
     CH6_YAW_KI 24
    // Rate
     CH6_ACRO_KP 25
     CH6_RATE_KP 4
     CH6_RATE_KI 5
     CH6_RATE_KD 21
     CH6_YAW_RATE_KP 6
     CH6_YAW_RATE_KD 26
    // Altitude rate controller
     CH6_THROTTLE_KP 7
    // Extras
     CH6_TOP_BOTTOM_RATIO 8
     CH6_RELAY 9
    // Navigation
     CH6_TRAVERSE_SPEED 10    // maximum speed to next way point
     CH6_NAV_KP 11
     CH6_LOITER_KP 12
     CH6_LOITER_KI 27

    // Trad Heli specific
     CH6_HELI_EXTERNAL_GYRO 13

    // altitude controller
     CH6_THR_HOLD_KP 14
     CH6_Z_GAIN 15
     CH6_DAMP 16        // duplicate with CH6_YAW_RATE_KD

    // optical flow controller
     CH6_OPTFLOW_KP 17
     CH6_OPTFLOW_KI 18
     CH6_OPTFLOW_KD 19

     CH6_NAV_I 20
     CH6_LOITER_RATE_KP 22
     CH6_LOITER_RATE_KI 28
     CH6_LOITER_RATE_KD 23

     CH6_AHRS_YAW_KP 30

  • Moderator

    Here Gareth

    CH6 STABILIZE KP = 1

    CH6 STABILIZE KI = 2

    CH6 STABILIZE KD = 29

    CH6 YAW KP = 3

    CH6 YAW KI = 24

    CH6 ACRO KP = 25

    CH6 RATE KP = 4

    CH6 RATE KI = 5

    CH6 RATE KD = 21

    CH6 YAW RATE KP = 6

    CH6 YAW RATE KD = 26

This reply was deleted.

Activity

DIY Drones via Twitter
RT @chr1sa: My talk on PX4 and FAA certification is coming up at 1:45 PST today on the PX4 Dev Summit livestream. Includes some cool new st…
Tuesday
DIY Drones via Twitter
RT @seesharp: I'm tuned into the PX4 / Dronecode free live conference. Great stuff. Microsoft AirSim talk in 10 minutes. https://t.co/0zbZ2…
Monday
DIY Robocars via Twitter
RT @masato_ka: 距離センサを3つとESP32を付けたラジコンカーをDonkeyCarライクにNNで自動走行。3層FC極小モデルをTensorFlow Lite for microcontrollerで動かしてる。機体は借り物でRumiCarって言います。Tenso…
Monday
DIY Robocars via Twitter
RT @SmallpixelCar: My car was able to go all the way autonomously until the crosswalk. It was only 100 yards from the target. What should b…
Saturday
Liam left a comment on Agricultural UAVs
"Hi
I'm Liam from T-MOTOR. I would like to reach out to see if there is any possibility for us to work together.
We are a propulsion system manufacturer who offers motors, propellers and ESCs for all kinds of drone applications which vary from secur…"
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Smart move. The car used the shadow to guide it through the bridge. This was never in the training samples. But it learn…
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Getting closer to the target. Single camera. Untrained road. https://t.co/Wsr7RwDamj
Jun 29
Richard Cox left a comment on Australia
"Anyone in the DIYDRONES Australian subgroup based in Alice Springs, NT?
I am experimenting with Ardupilot (standard Arduplane), Pixhawk 4 FC in a 4-ch
RC "AXN Floater Jet" foamy plane..."
Jun 29
Omar Sykes left a comment on Australia
"Hi everyone, I am looking for someone who is good at drone building, repair and software in Adelaide. Please give me a call on 0477 319 219."
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: #donkeycar https://t.co/czuLoVRcA4
Jun 29
DIY Robocars via Twitter
https://t.co/DKQbNTbz0g
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: Donkey car, car car car car car car; Donkey car, car car car car car car; Donkey Car. Anyone like our tiny tiny donkey…
Jun 29
DIY Robocars via Twitter
RT @SmallpixelCar: After improving DBSCAN speed, I can get 11 frame per second on @NVIDIAEmbedded Jerson Xavier MAXN mode and the autonomou…
Jun 26
DIY Robocars via Twitter
RT @Heavy02011: Join us at next Virtual Race League: ⁦@diyrobocars⁩ Race #4 - Parking Lot Nerds, August 1st https://t.co/5KUpu7VGaH
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: #CUDA implementation should be easy, because most of the time is on distance calculations berween two points and if the…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: This is the view from the car. Even my lanenet inference is fast on @NVIDIAEmbedded Jerson Xavier, DBSCAN clustering tak…
Jun 25
More…