Increasing flight time

Hello all!I'm currently using a 2200ma LiPo battery on board my craft. I'm getting 5 minutes of flying time. This is way to short for what I need it to do. I would love to get at least 15 minutes. Is that possible? 

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Lower KV motors, bigger props, and the ESC's to drive them.

  • @Nano -

     

    With a 2kg quad, 11ah 4s battery, NX 4006 530kv motors, and APC 14x4.7 props,  I was getting a reliable 35 minutes of flight time in actual flying conditions.

     

    The battery did cost $300 though.  Since I was carrying a lot of extra (non flight) batteries for the vTx and other components, you should expect similar results with less expensive (cheaper) batteries.

    • Hello Arashi,

      I have a 2.2Kg quad (with 4S 10,000) running the NX-4006 motors on Graupner 14x8 props, and despite all ESCs are properly calibrated, i find that the quad feels very low on power - i have to set the throttle mid point in APM (it ranges 300-700) to full 700 to maintain a steady hover at half stick! i seriously doubt my motors are putting 1+Kg thrust each!

      any tips where to look? how did yours feel compared to mine?

      thanks.

  • Have a look to my post on that

    http://diydrones.com/forum/topics/quadropter-flight-time-1
  • 100KM

    Use a bigger battery and more powerfull motors at the right proportions to get your targeted flighttime.

  • Moderator

    What is your AUW? What motors, ESCs, and props are you using?

This reply was deleted.

Activity

DIY Robocars via Twitter
https://t.co/bzpbxytpsv
13 hours ago
DIY Drones via Twitter
RT @chr1sa: My talk on PX4 and FAA certification is coming up at 1:45 PST today on the PX4 Dev Summit livestream. Includes some cool new st…
Tuesday
DIY Drones via Twitter
RT @seesharp: I'm tuned into the PX4 / Dronecode free live conference. Great stuff. Microsoft AirSim talk in 10 minutes. https://t.co/0zbZ2…
Jul 6
DIY Robocars via Twitter
RT @masato_ka: 距離センサを3つとESP32を付けたラジコンカーをDonkeyCarライクにNNで自動走行。3層FC極小モデルをTensorFlow Lite for microcontrollerで動かしてる。機体は借り物でRumiCarって言います。Tenso…
Jul 5
DIY Robocars via Twitter
RT @SmallpixelCar: My car was able to go all the way autonomously until the crosswalk. It was only 100 yards from the target. What should b…
Jul 4
Liam left a comment on Agricultural UAVs
"Hi
I'm Liam from T-MOTOR. I would like to reach out to see if there is any possibility for us to work together.
We are a propulsion system manufacturer who offers motors, propellers and ESCs for all kinds of drone applications which vary from secur…"
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Smart move. The car used the shadow to guide it through the bridge. This was never in the training samples. But it learn…
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Getting closer to the target. Single camera. Untrained road. https://t.co/Wsr7RwDamj
Jun 29
Richard Cox left a comment on Australia
"Anyone in the DIYDRONES Australian subgroup based in Alice Springs, NT?
I am experimenting with Ardupilot (standard Arduplane), Pixhawk 4 FC in a 4-ch
RC "AXN Floater Jet" foamy plane..."
Jun 29
Omar Sykes left a comment on Australia
"Hi everyone, I am looking for someone who is good at drone building, repair and software in Adelaide. Please give me a call on 0477 319 219."
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: #donkeycar https://t.co/czuLoVRcA4
Jun 29
DIY Robocars via Twitter
https://t.co/DKQbNTbz0g
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: Donkey car, car car car car car car; Donkey car, car car car car car car; Donkey Car. Anyone like our tiny tiny donkey…
Jun 29
DIY Robocars via Twitter
RT @SmallpixelCar: After improving DBSCAN speed, I can get 11 frame per second on @NVIDIAEmbedded Jerson Xavier MAXN mode and the autonomou…
Jun 26
DIY Robocars via Twitter
RT @Heavy02011: Join us at next Virtual Race League: ⁦@diyrobocars⁩ Race #4 - Parking Lot Nerds, August 1st https://t.co/5KUpu7VGaH
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: #CUDA implementation should be easy, because most of the time is on distance calculations berween two points and if the…
Jun 25
More…