Pixhawk weird behaviour

I bought Radiolink Pixhawk a few days ago. Loaded it with APM plane 3.9 and mounted it on my flying wing. Did all bench test like stabilizing, failsafe trigger and power module tuning. All worked well and i also did a test flying. During first flight it behaved normal, i tested stabilize mode and it was stabilizing the wings but with nose down posture so i thought i need to do acclerometer calibration again by keeping nose a bit up so that it can maintain level flight. I also connected mavlink to TBS diversity receiver and i was getting flight data from pixhawk to ground TBS crossfire tx module on Tower app on my android through bluetooth.

Now next day i did calibration and my buddy launched the craft just after takeoff motor shut down and i had no control from transmitter. I did another launch same thing happened again. As my buddy launch the wing within 1sec it cuts the throttle and the rc control. 

So i reinstalled the firmware and did all mandatory stuff. Then i tested it on bench. I found that after arming as i increase throttle more than 50% it cut the radio signals and after 3 sec it cuts the throttle. Pixhawk reboots  it self. At first i thought it can be a faulty power module. So i changed it with my old trusted one. Then tested in workshop( bench test) there it worked fine it was not cutting the signals and i had control over power.

Next day at flying field i took off and did some circuiting checked stabilize, it behaved weird so back to manual. After 1 min. for flying i suddenly lost the radio signal and craft crashed it the ground with resumed throttle. There is no problem with radio, it works very well because i've tested it over 15 miles.

i can't figure out what is wrong with it. 

Following stuff i used-

Radiolink pixhawk with M8N Gps

TBS Crossfire radio system with diversity receiver providing PPM out.

Turnigy 9xr Pro

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –
This reply was deleted.

Activity

DIY Drones via Twitter
RT @chr1sa: My talk on PX4 and FAA certification is coming up at 1:45 PST today on the PX4 Dev Summit livestream. Includes some cool new st…
Tuesday
DIY Drones via Twitter
RT @seesharp: I'm tuned into the PX4 / Dronecode free live conference. Great stuff. Microsoft AirSim talk in 10 minutes. https://t.co/0zbZ2…
Monday
DIY Robocars via Twitter
RT @masato_ka: 距離センサを3つとESP32を付けたラジコンカーをDonkeyCarライクにNNで自動走行。3層FC極小モデルをTensorFlow Lite for microcontrollerで動かしてる。機体は借り物でRumiCarって言います。Tenso…
Monday
DIY Robocars via Twitter
RT @SmallpixelCar: My car was able to go all the way autonomously until the crosswalk. It was only 100 yards from the target. What should b…
Saturday
Liam left a comment on Agricultural UAVs
"Hi
I'm Liam from T-MOTOR. I would like to reach out to see if there is any possibility for us to work together.
We are a propulsion system manufacturer who offers motors, propellers and ESCs for all kinds of drone applications which vary from secur…"
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Smart move. The car used the shadow to guide it through the bridge. This was never in the training samples. But it learn…
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Getting closer to the target. Single camera. Untrained road. https://t.co/Wsr7RwDamj
Jun 29
Richard Cox left a comment on Australia
"Anyone in the DIYDRONES Australian subgroup based in Alice Springs, NT?
I am experimenting with Ardupilot (standard Arduplane), Pixhawk 4 FC in a 4-ch
RC "AXN Floater Jet" foamy plane..."
Jun 29
Omar Sykes left a comment on Australia
"Hi everyone, I am looking for someone who is good at drone building, repair and software in Adelaide. Please give me a call on 0477 319 219."
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: #donkeycar https://t.co/czuLoVRcA4
Jun 29
DIY Robocars via Twitter
https://t.co/DKQbNTbz0g
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: Donkey car, car car car car car car; Donkey car, car car car car car car; Donkey Car. Anyone like our tiny tiny donkey…
Jun 29
DIY Robocars via Twitter
RT @SmallpixelCar: After improving DBSCAN speed, I can get 11 frame per second on @NVIDIAEmbedded Jerson Xavier MAXN mode and the autonomou…
Jun 26
DIY Robocars via Twitter
RT @Heavy02011: Join us at next Virtual Race League: ⁦@diyrobocars⁩ Race #4 - Parking Lot Nerds, August 1st https://t.co/5KUpu7VGaH
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: #CUDA implementation should be easy, because most of the time is on distance calculations berween two points and if the…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: This is the view from the car. Even my lanenet inference is fast on @NVIDIAEmbedded Jerson Xavier, DBSCAN clustering tak…
Jun 25
More…