Pixhawk weird behaviour

I bought Radiolink Pixhawk a few days ago. Loaded it with APM plane 3.9 and mounted it on my flying wing. Did all bench test like stabilizing, failsafe trigger and power module tuning. All worked well and i also did a test flying. During first flight it behaved normal, i tested stabilize mode and it was stabilizing the wings but with nose down posture so i thought i need to do acclerometer calibration again by keeping nose a bit up so that it can maintain level flight. I also connected mavlink to TBS diversity receiver and i was getting flight data from pixhawk to ground TBS crossfire tx module on Tower app on my android through bluetooth.

Now next day i did calibration and my buddy launched the craft just after takeoff motor shut down and i had no control from transmitter. I did another launch same thing happened again. As my buddy launch the wing within 1sec it cuts the throttle and the rc control. 

So i reinstalled the firmware and did all mandatory stuff. Then i tested it on bench. I found that after arming as i increase throttle more than 50% it cut the radio signals and after 3 sec it cuts the throttle. Pixhawk reboots  it self. At first i thought it can be a faulty power module. So i changed it with my old trusted one. Then tested in workshop( bench test) there it worked fine it was not cutting the signals and i had control over power.

Next day at flying field i took off and did some circuiting checked stabilize, it behaved weird so back to manual. After 1 min. for flying i suddenly lost the radio signal and craft crashed it the ground with resumed throttle. There is no problem with radio, it works very well because i've tested it over 15 miles.

i can't figure out what is wrong with it. 

Following stuff i used-

Radiolink pixhawk with M8N Gps

TBS Crossfire radio system with diversity receiver providing PPM out.

Turnigy 9xr Pro

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –
This reply was deleted.

Activity

DIY Robocars via Twitter
RT @a1k0n: @SmallpixelCar @diyrobocars It's just something that's easy to track with chroma keying. I ended up using different colors on th…
15 hours ago
DIY Robocars via Twitter
15 hours ago
DIY Robocars via Twitter
RT @TinkerGen_: "The Tinkergen MARK ($199) is my new favorite starter robocar. It’s got everything — computer vision, deep learning, sensor…
Nov 23
DIY Robocars via Twitter
Nov 23
DIY Robocars via Twitter
RT @roboton_io: Join our FREE Sumo Competition 🤖🏆 👉 https://roboton.io/ranking/vsc2020 #sumo #robot #edtech #competition #games4ed https://t.co/WOx…
Nov 16
DIY Drones via Twitter
First impressions of Tinkergen MARK robocar https://ift.tt/36IeZHc
Nov 16
DIY Robocars via Twitter
Our review of the @TinkerGen_ MARK robocar, which is the best on the market right now https://diyrobocars.com/2020/11/15/first-impressions-of-tinkergen-mark-robocar/ https://t.co/ENIlU5SfZ2
Nov 15
DIY Robocars via Twitter
RT @Ingmar_Stapel: I have now explained the OpenBot project in great detail on my blog with 12 articles step by step. I hope you enjoy read…
Nov 15
DIY Robocars via Twitter
RT @DAVGtech: This is a must attend. Click the link, follow link to read the story, sign up. #chaos2020 #digitalconnection #digitalworld ht…
Nov 15
DIY Robocars via Twitter
RT @a1k0n: Got a new chassis for outdoor races (hobbyking Quantum Vandal) but I totally didn't expect that it might cause problems for my g…
Nov 11
DIY Drones via Twitter
First impressions of the Intel OpenBot https://ift.tt/36qkVV4
Nov 10
DIY Robocars via Twitter
Nov 9
DIY Robocars via Twitter
Excellent use of cardboard instead of 3D printing! https://twitter.com/Ingmar_Stapel/status/1324960595318333441
Nov 7
DIY Robocars via Twitter
RT @chr1sa: We've got a record 50 teams competing in this month's @DIYRobocars @donkey_car virtual AI car race. Starting today at 10:00am…
Nov 7
DIY Robocars via Twitter
Nov 6
DIY Robocars via Twitter
RT @a1k0n: Car's view, using a fisheye camera. The ceiling light tracking algorithm gave me some ideas to improve ConeSLAM, and having grou…
Nov 5
More…