Problem connecting Pixhawk and Futaba receiver


Two of my customers have trouble setting up the Pixhawk - I myself have a Pixhawk, but don't use a Futaba receiver, thereby I can't replicate the problem (I would like to find out if the problem is connected to the receiver they use, or something else).

Both use a Futaba R7008SB receiver.
Both managed to upload the Firmware to their Pixhawks - but they are not able to do the radio calibration (the Pixhawk doesn't "see" the receivers, the bars in the calibration are all grey).

They have nothing else connected to the Pixhawk, except receiver (connected to the right port / RC), buzzer, safety switch and USB cable.

The Pixhawk signals via the big LED "pre-arm check failed" (which makes sense ;)

They power the Pixhawk via USB and at the same time with a LiPo (via the Power Module).

The receiver is "found" by the remote, the LEDs are on, the setting of receiver and remote (regarding the use of the SBUS) seems to be right. They use the right port of the receiver to connect to the Pixhawk.

I am happy about any suggestions ...

Thanks a lot in advance


You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –


  • Try asking here:


    Drone Pilot Jobs
    Share Drone Pilot Job Offers/Demand, please Contact for promotional posts in adronepilot@gmail.com Comparte tus anuncios de compraventa de drones…
  • Yes, I have managed to do this but I believe I accomplished this with an R7008SB receiver in mode D. I dont have the unit anymore but I had to upgrade to firmware 3.2 from 3.1.5 for it to work. What firmware are you on? 

    • Hi and thanks very much for the reply.

      Unfortunately I know almost nothing about RC systems and Futaba products, so I really do not know, I will google though to get an understanding.

      Did you get all 14 channels? I mean if you connected something on RC11 it woud correspond to Futaba's AUX 11?

      Thanks again

      • Hi,
        I am interested with Pixhawk and planning to buy one. but can I use it with my jr xg14 transmitter and rgrg731bx DMSS receiver? is it compatible with JR DMSS system?

        FARSEZ is online now Send a private message to FARSEZ Find More Posts by FARSEZ
        RC Groups
        RC Groups - the most active Radio Control model community: electric and fuel rc airplanes,rc helis,rc boats and rc cars. Features discussion forums,…
  • Hi there,

    I am a Pixhwak user on a hexacopter and trying to get 14 channels out of the pixhwahk connected to a Futaba 6208Sb receiver. Has anyone achieved this sucesfully? Futaba manual says that you can set the receiver to mode B and get an extra set of 8 channels on the pin ports. IS this true?

    Thanks for your time


  • Dear Martin,
    I had my first flight yesterday with pixhawk integrated. To my surprise we had a nice flight without any issues. I could try out almost all the modes (Stabilize, FBWA,FBWB, Loiter, Auto etc.). It was absolutely fine, had to do little bit of tuning, but still a lot of work is left. The good thing is I could do all these without connecting the PPM encoder also .The pixhawk was not responding before, because I was not depressing the safety switch before arming it. I think this is an important step that everyone should know, Thanks a lot for your support...
  • Dear Martin,
    Thank you very much for the reply. I will get back to you after my flight...
    Thank you
  • This is the switch port you can see at the centre of the Pixhawk. I is the between the telemetry and serial ports,
    • Moderator
      Hi madhuraj,
      No problems, that's the safety switch! You are required to depress the switch each time you arm the copter, it has 3 light displays. Quick and constant blinking is it performing a system check, just wait until it finishes- it should then go to slow constant blinking meaning that it is ready to arm. You should only need to press it for a few seconds if you have waited until the checks have been completed. It will then go to solid red meaning that it is ready to arm on your transmitter. Sometimes it will take a long time to arm as it performs the pre arm checks, especially if you are trying to take off in a gps assisted mode as it will wait until the gps is up and running (30secs or so). If so try arming in stabilise but do give it time before going to GPS assist modes. I always arm in stabilise but check GPS status beforehand. You can disarm the safety checks in mission planner but I do not recommend it unless you are well aware of the system, it is there to look after you!
      Hope it goes well, let me know if you have any issues,

This reply was deleted.


DIY Drones via Twitter
RT @Struktur3D: We have just posted on @DIYDrones for the first time in a long time. Continuing with our search for a #lasercutting service…
DIY Robocars via Twitter
RT @chr1sa: The dev team is having fun with virtual @DIYRobocars track generation with Unity on the @donkey_car discord: https://t.co/l0Jd9…
DIY Drones via Twitter
Review of the new Nivida Jetson NX for robocars https://t.co/bWjd3sH2o4
DIY Robocars via Twitter
RT @chr1sa: My review of the new @NVIDIAEmbedded Jetson Xavier NX in robotics and @DIYRobocars applications https://t.co/O7TfJZhiF9 https:/…
DIY Drones via Twitter
RT @chr1sa: Somehow I missed this, but last week @Nvidia released a new version of its Isaac robot development framework. Lots of new Lidar…
May 31
DIY Robocars via Twitter
RT @Smartphone89: DonkeyCar Racing League Korea #donkeycar @diyrobocars https://t.co/mDlHDR1d98
May 29
Jørn Ramnæs liked VIDEO LINK's profile
May 28
Mark Harrison left a comment on Moderators
"Wow, Ning2 looks really great on mobile. I had sort of drifted away as my browse-time went more on my phone, so this is great."
May 28
DIY Robocars via Twitter
May 28
DIY Drones via Twitter
Welcome to the new DIY Drones design!. You may have noticed that DIY Drones looks a little different today. That's… https://t.co/cg2EmeDGMQ
May 27
DIY Drones via Twitter
New! Online Training on Drones for Disaster Response https://t.co/brqRuujjY2
May 26
DIY Robocars via Twitter
May 25
DIY Robocars via Twitter
RT @OttawaAVGroup: We are going to try something new this week. We will be having a drop-in style meeting Wednesday @ 7-9pm EST. Pop in and…
May 25
DIY Robocars via Twitter
RT @tawnkramer: Thanks Everyone for another fun virtual race! Amazing Ai racers competing head-to-head, Virtual Makers Fair event. Catch us…
May 23
DIY Robocars via Twitter
RT @make: Find out the latest from @diyrobocars at 10am PT from @chr1sa of @3DRobotics on Virtually Make Faire! #makerfaire #maketogether #…
May 23
DIY Robocars via Twitter
RT @Heavy02011: Join us Saturday online: Virtual Race League: @DIYRobocars Race #2 - Parking Lot Nerds https://t.co/aJUu4sdutx #Meetup via…
May 22