Quad suddenly dropped from the sky!

Hey All,

I was wondering if someone could confirm a hardware failure from looking at this log for me?


My setup:

APM 2.5 with internal compass

3DR Quad kit (essentially this one: http://store.3drobotics.com/products/3dr-arducopter-quad-c-frame-kit-1 but I bought it with the uBlox LEA-6 GPS module before the compass was included)

3S-4000mah battery (fully charged and balanced before the flight)

10x4.7 props (balanced but some minor battle nicks on them)

850kv blue motors

Moon Gel pads (double layer) under the corners of the APM and APM secured to top plate with rubberbands

3DR Telemetry radios


I have done all of the calibrations and scored a 7% on my compassmot test! :-)  I do not recall my vibration test results but they were well within margins.


The day here was partially cloudy, about 55F (a nice summer day in Alaska!) with wind gusting up to about 15mph and about 10 steady coming from behind me as I faced the quad.


I had already done a successful flight previous to this one with no problems.  I was testing loiter and RTL on the first flight as well as just flying around practicing circles and nose-in and nose-out orientations.  I swapped batteries and allowed over 5 minutes between flights for the APM to warm up and settle out.


During this flight I was mostly again testing Loiter with a bit of RTL and some basic forward and back maneuvers along with side to side.  Some friends dropped by while I was flying so I basically parked the Quad in a Loiter and talked to them while still keeping and eye on the quad.


After a few minutes of talking and loitering we all just watched the quad sort of dip one arm and fall from the sky.  It wasn't a tumbling type of a fall, it was flat but sort of wobbly as it fell pretty much straight down.  Luckily it had been raining for the last 5 days so the field I was flying over was really soft and there wasn't any real damage except for the landing gear which cracked.  One arm/motor was buried in the soft dirt and were stopped but the other 3 were still spinning.  Moving the throttle had no effect and trying to disarm didn't either.  I thought about letting the battery run itself out but then decided to carefully reach under the quad and unplug the battery.  As I think about it now I was probably still in Loiter mode and simply switching to Stabilize probably would've allowed me to disarm normally but it didn't occur to me at the time.


Anyway, that was my flight.  I took a look at the log tutorial and to me it looks like when I graph the roll values and the pitch values that a mechanical error occurred but I am certainly no expert reading/graphing the log data.  If someone could confirm this I would be very grateful.




2013-08-11 19-05 6.log

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –


  • Hi Mike and/or Wessie, I have been having what sounds like identical problems with both my APM quad and hex.  Did you ever resolve this beyond changing out the ESC?  I have built 2 new machines with different ESCs (different brands even) and still have the problem. ThrOut suddenly drops, then there is a major roll issue as the machine drops to the ground.  No issues with any of my fixed wings running APM though...  So frustrating!!



  • Hi

    Just had a look at your Log.

    Findings so far:

    You had around 10 sats all the time, so not GPS glitch

    Mode was in LOITER all the time, so not "mode change glitch"

    Battery always above 10.5V

    3692799339?profile=originalUp to the point Line 16400 everything seemed hunkey dory, then suddenly your output throttle went wild.
    Unfortunately I have no idea why it did this.


    Barometer VS WP Alt (Above) looks great as well, except that AFTER the quad started to fall, the WPAlt went as well. I would have expected it to stay.

    I do think I have a possible idea how the problem manifests itself, but no idea what causes it. Will start a new thread to see if it is something we can replicate, and needs looking into. If I am right, it will explain quite a number of unsolved crashes reported lately, including mine.

  • Sorry about your quad Mike!

    I didn't look at your logs yet but the description sounds similar to what i experienced with my hexa recently.

    here is my post and theres a video of the actual motor stop. http://diydrones.com/forum/topics/need-some-help-with-these-logs

    Does that look similar to what you experienced?

  • 3D Robotics

    Yes, that sounds like a mechanical problem: a motor, prop collet, or motor connection failed. 

This reply was deleted.


DIY Robocars via Twitter
RT @SahikaGenc: AWS DeepRacer & Hot Wheels Track https://youtu.be/4H0Ei07RdR4 via @YouTube
Sep 14
DIY Robocars via Twitter
Sep 8
DIY Robocars via Twitter
RT @davsca1: We are releasing the code of our Fisher Information Field, the first dedicated map for perception-aware planning that is >10x…
Sep 8
DIY Robocars via Twitter
RT @SmallpixelCar: How this works: 1)object detection to find cones in single camera image, 30 frames/sec on @NVIDIAEmbedded Xavier. 2)comp…
Sep 8
DIY Robocars via Twitter
RT @SmallpixelCar: Use two color cones to guide the robocar. No map needed, on onsite training needed. Just place the cones and it will fol…
Sep 7
DIY Robocars via Twitter
Sep 7
DIY Robocars via Twitter
RT @roboton_io: Great to see http://roboton.io running at 60fps on the cheapest #chromebook we could find! #edtech #robotics #educat…
Sep 3
DIY Robocars via Twitter
RT @openmvcam: Crazy in-depth article about using the OpenMV Cam for Astrophotography: https://github.com/frank26080115/OpemMV-Astrophotography-Gear https://t.co/BPoK9QDEwS
Sep 3
DIY Robocars via Twitter
RT @openmvcam: Hi folks, it's finally here! Our first draft of our Arduino Interface Library is out! It works over SoftwareSerial, Hardware…
Sep 3
DIY Robocars via Twitter
RT @chr1sa: Please let them have an open API. This would be perfect for @DIYRobocars races https://twitter.com/NintendoAmerica/status/1301513099707658246
Sep 3
DIY Robocars via Twitter
RT @SmallpixelCar: Lanenet pretty much used all my GPU power on @NVIDIAEmbedded Xavier since I optimized with tensorRT. I need to run anoth…
Sep 3
xemone liked Max Gilson's profile
Aug 31
DIY Robocars via Twitter
RT @LyftLevel5: Our @kaggle competition on Motion Prediction for Autonomous Vehicles is now live! Experiment with the largest-ever self-dri…
Aug 24
DIY Robocars via Twitter
RT @chr1sa: Our next @DIYRobocars virtual AI car race will be on Sept 26th. Sign up here https://www.meetup.com/DIYRobocars/events/272786977/ https://t.co/UENKGSOWO8
Aug 24
DIY Robocars via Twitter
New ready-to-run @NVIDIAEmbedded JetRacer car from Waveshare. Perfect for the next @diyrobocars race as soon as we… https://twitter.com/i/web/status/1297960223013867520
Aug 24
DIY Drones via Twitter
RT @chr1sa: The US government just approved 5 US-made drones for purchase, all based on the @Dronecode @PX4Autopilot standard. Great news f…
Aug 20