Tarot Gimble on X8

Hi, 

i have a 3DR X8 and have have been trying to get the gimble to work fo a week now..  I have followed every instruction to the letter.

Upload latest Firmware - Check (to both motors and Board)

Load 3DR recomened settings - Check

i have been though the process  a million times ot make sure its OK.. 

on the BMGC software all the saner does is spin it does not seem to level at al;l see vid attached

it does not resond to any movemnt of drone - leveling etc..  it tilts and rolls with the drone.

I am not sure if its Faulty ot what?

any help apreciated.

IMG_6744.MOV

IMG_6745.MOV

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Did you point the gimbal strait up and run the calibrate gimbal button?

    • I wonder if you have solved your problem?

      There is a very clear Youtube video showing exactly what to do:

      https://www.youtube.com/watch?v=zXsvsYbW09E

      I discovered that it is necessary (for me) to increase the motor power in the motor power setup, since I have an FPV camera attached to the Go Pro too, adding more load to the Roll motor. So I have increased the Roll to 80% and the Tilt to 45. Seems to do the trick.

      Hope this helps.

      Tarot Gopro+FPV cam.jpg

      • Hi David,  great stuff and thanbks for your reply its much apreacited..   i hav ebene traveling for the past few months and have not had the X8 out for a while but never had got around to fixing this gimble bit will for sure now give it a crack.   Thansk again.. Chris 

  • OK, I have the same gimbal so i'll try.

    First, does the software connect to it? (I assume so). What firmware? I'm using 1.5. Disconnect from your receiver / APM etc until it works fine without.

    Connect to the motor port, load the motor GoPro default config file and write that. That sets it to power 60 for roll and 35 for tilt IIRC.

    Now connect to the gimbal port, and connect.

    Next,turn the motors off (in the software), prop the camera so it's level, lying flat on it's back looking skywards, and press the calibrate button.

    Now load the default GoPro config file that came with the software for the gimbal, and write the parameters.

    Turn on the motors and see if it's better.

    If you need the default files, let me know and i'll post them.

    I've found the defaults are a good starting point.

    • HI Alan, thanks for your reply and apologies for my late response but traveling for work,  i really have done the config as per instructions but it still all crazy.. i used the recommended 3DR setup and it was to load 1.4.

      any files you could help us with woudl be awesome..  i am having another go at it this weekend.

      Cheers

      Chris

      • Attached are the default config files that were supplied with my gimbal. I'm using these with Firmware v1.5 and a GoPro Hero 3+ and it works really well.

        Your videos look like a calibration issue, I had similar when I accidentally pressed the calibration button.

        As mentioned before, set the camera flat on it's back and pointing straight up (and still), then press calibrate again.

        gopro.bgsc

        gopro.bmc

        https://storage.ning.com/topology/rest/1.0/file/get/3702651138?profile=original
This reply was deleted.

Activity

DIY Robocars via Twitter
RT @chr1sa: The dev team is having fun with virtual @DIYRobocars track generation with Unity on the @donkey_car discord: https://t.co/l0Jd9…
yesterday
DIY Drones via Twitter
Review of the new Nivida Jetson NX for robocars https://t.co/bWjd3sH2o4
Tuesday
DIY Robocars via Twitter
RT @chr1sa: My review of the new @NVIDIAEmbedded Jetson Xavier NX in robotics and @DIYRobocars applications https://t.co/O7TfJZhiF9 https:/…
Monday
DIY Drones via Twitter
RT @chr1sa: Somehow I missed this, but last week @Nvidia released a new version of its Isaac robot development framework. Lots of new Lidar…
Monday
DIY Robocars via Twitter
RT @Smartphone89: DonkeyCar Racing League Korea #donkeycar @diyrobocars https://t.co/mDlHDR1d98
May 29
Jørn Ramnæs liked VIDEO LINK's profile
May 28
Mark Harrison left a comment on Moderators
"Wow, Ning2 looks really great on mobile. I had sort of drifted away as my browse-time went more on my phone, so this is great."
May 28
Hank Deucker left a comment on PIXHAWK
"I am sure most will say not again, Pixhawk telemetry. I do need help and all can be reassured that I have spent many hours scouring the net for useful information. I am not new at quadcopter flying, I started in 2012 and have progressed through many…"
May 28
DIY Robocars via Twitter
https://t.co/rLmFr8M2UK
May 28
DIY Drones via Twitter
Welcome to the new DIY Drones design!. You may have noticed that DIY Drones looks a little different today. That's… https://t.co/cg2EmeDGMQ
May 27
DIY Drones via Twitter
New! Online Training on Drones for Disaster Response https://t.co/brqRuujjY2
May 26
DIY Robocars via Twitter
https://t.co/8EMCvYW6oz
May 25
DIY Robocars via Twitter
RT @OttawaAVGroup: We are going to try something new this week. We will be having a drop-in style meeting Wednesday @ 7-9pm EST. Pop in and…
May 25
DIY Robocars via Twitter
RT @tawnkramer: Thanks Everyone for another fun virtual race! Amazing Ai racers competing head-to-head, Virtual Makers Fair event. Catch us…
May 23
DIY Robocars via Twitter
RT @make: Find out the latest from @diyrobocars at 10am PT from @chr1sa of @3DRobotics on Virtually Make Faire! #makerfaire #maketogether #…
May 23
DIY Robocars via Twitter
RT @Heavy02011: Join us Saturday online: Virtual Race League: @DIYRobocars Race #2 - Parking Lot Nerds https://t.co/aJUu4sdutx #Meetup via…
May 22
More…