Turnigy 9x ppm and failsafe

Hi all, first post, hope it's in the right section..

I'm currently trying to setup failsafe arducopter v2.3 and turnigy 9x v2 but I'm now stuck...

I set thr_failsafe = 1 and thr_fs_action = 2

I suppose that the failsafe function is enabled when all channel send 0-975 signal or the radio is swicthed off. 

Well, for what I'm seeing the original receiver of the turnigy 9x in PPM sends to the arducopter the last signal received. i.e. throttle at 60% and stays there,  unless you haven't enabled the failsafe function in the radio menu. But, as stated in the manual, it works only in PCM mode ( as far as I understand this is valid for other radios, too).

If I enable PCM mode, all the channells get crazy... throttle included... (no props attached!)

I'm pretty sure I'm missing something... if anyone can help it would be appreciated,

thanks

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I have the same radio.  Failsafe does not work in PPM mode.. just PCM. You need to do what I did.

    I bough a FRsky transmitter and receiver module.  I't worth the money, you will get better range too.

    Failsafe with the turnigy/frsky is a piece of cake.   I set mine for RTL.

    Make sure you set the radio up for it correctly, if you use the default settings all motors will stop and it will fall like a brick.

  • It works out of the box just fine if it's a genuine 3DRobotics APM 2.6, none of the clones I've bought from China have worked.

  • Stock Turnigy 9X with the stock 9X8Cv2 receiver has got a configurable failsafe for signal loss. 

    -Set the transmitter to PPM in SYSTEM SETTINGS->MODEUAT/MODULATION->PPM 

    -Set FUNC SETTING->E.POINT->THROTTLE to 120%/120% (This changes the maximum throw up&down. protip: move throttle stick to change value for up/down...)

    -Set FUNC SETTING->SUBTRIM->THROTTLE to -120 (sets the midpoint lower, so that the failsafe value goes to less than 1000

    -Set FUNC SETTING->FAIL SAF->THR->F/S 000% (This sets the failsafe (transmitter off) value to 0%, which goes -to <1000 since we changed the midpoint/endpoints. In my system, the failsafe value is 900 and min throttle 981.

    -Adjust your throttle trim and APM/multiwii/etc. failsafe thresholds so that the failsafe signal value is lower & failsafe is correctly activated in your autopilot. Poke, Test, poke and test. Don't rely on the default values!

    Note: My Turnigy transmitter&receiver are a few years old from Hobby King. Your results may vary. Tested on [SYSTEM SETTINGS->TYPE SELECT->ACRO] model type. Not sure if everything are the same for GLIDE&HELI. Also the Turnigy is a cheap-ass system, consider something better for anything valuable&dangerous. :)

    Some pics of menus: https://www.dropbox.com/sc/9qmdbg1m1fqkmvy/PNpV77VN0n 

    Turnigy9Xfailsafe (1) (6 photos)
    Shared with Dropbox
  • I am having a problem with a Turnigy 9xBC version 2 RX when there is an absent of a signal from the trnsmitter(turned off), it output the last value received from the TX signal on Channels 4 and 5.  I have gone into the transmitter setup, switched to PCM and tried to disable any failsafe setting there but the RX but it still outputs a signal on channels 4 and 5 regardless.  This is not good for the simple Servo to PPM encoder that I would like to use.

  • Please can I ask what you guys think of THIS motor.

    Thank You

  • As fat as I understand the failsafe in T9X is only working for PCM, and not PPM that the 2.4 GHZ modules uses, and as such not available.

This reply was deleted.

Activity

DIY Drones via Twitter
RT @chr1sa: Somehow I missed this, but last week @Nvidia released a new version of its Isaac robot development framework. Lots of new Lidar…
19 hours ago
DIY Robocars via Twitter
RT @Smartphone89: DonkeyCar Racing League Korea #donkeycar @diyrobocars https://t.co/mDlHDR1d98
Friday
Jørn Ramnæs liked VIDEO LINK's profile
Friday
Mark Harrison left a comment on Moderators
"Wow, Ning2 looks really great on mobile. I had sort of drifted away as my browse-time went more on my phone, so this is great."
Friday
Hank Deucker left a comment on PIXHAWK
"I am sure most will say not again, Pixhawk telemetry. I do need help and all can be reassured that I have spent many hours scouring the net for useful information. I am not new at quadcopter flying, I started in 2012 and have progressed through many…"
Thursday
DIY Robocars via Twitter
https://t.co/rLmFr8M2UK
Thursday
Hank Deucker left a comment on PIXHAWK
"Tomorrow, I am thinking about the wording at the moment."
Thursday
DIY Drones via Twitter
Welcome to the new DIY Drones design!. You may have noticed that DIY Drones looks a little different today. That's… https://t.co/cg2EmeDGMQ
Wednesday
DIY Drones via Twitter
New! Online Training on Drones for Disaster Response https://t.co/brqRuujjY2
May 26
DIY Robocars via Twitter
https://t.co/8EMCvYW6oz
May 25
DIY Robocars via Twitter
RT @OttawaAVGroup: We are going to try something new this week. We will be having a drop-in style meeting Wednesday @ 7-9pm EST. Pop in and…
May 25
DIY Robocars via Twitter
RT @tawnkramer: Thanks Everyone for another fun virtual race! Amazing Ai racers competing head-to-head, Virtual Makers Fair event. Catch us…
May 23
DIY Robocars via Twitter
RT @make: Find out the latest from @diyrobocars at 10am PT from @chr1sa of @3DRobotics on Virtually Make Faire! #makerfaire #maketogether #…
May 23
DIY Robocars via Twitter
RT @Heavy02011: Join us Saturday online: Virtual Race League: @DIYRobocars Race #2 - Parking Lot Nerds https://t.co/aJUu4sdutx #Meetup via…
May 22
DIY Robocars via Twitter
RT @donkey_car: Yay, we are part of the virtual @makerfaire with @diyrobocars. Come see our race or better yet train a model and race with…
May 21
DIY Robocars via Twitter
RT @chr1sa: The @DIYRobocars Virtual AI Race is going to be part of the virtual @makerfaire on Sat! https://t.co/wnMDAboLID
May 20
More…