100KM

upload fail

I am having problem with upload command from flight data. Eg Change altitude, restart mission ect. I do not have this type of problem with the previous Mission Planner. When I try to change altitude, a fail massage window appear. I also can not write param to APM while flying. But if the plane had landed and close by my computer, there is no problem. Anyway I can establish connection between the two data modem with ease.

I'm using RDF900,  am I doing something wrong in 3dr radio setting ? Thanks for your help.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I don't know which is best I guess I just assumed a high gain antenna on each end would be good if possible. But I really don't know.

    One interesting thing I noticed is I have an older version of mission planner that has the 3DR radio set up and the power options goes up to 30 unlike the newer versions that only go up to 20. I also noticed the RFD900 data sheet suggests a range of apron 10 miles. I think it used to say 30. Not sure why that is. But after I set mine to 30 it got noticeably warm. not hot.. but you could tell it was working at the 30 power level.  And yet another observation... another RFD900 with the same settings on the ground side does not get warm. I wonder if this is because the air side radio is doing all the 'talking'??

    • U should still be able to go to 30dBm. Use rfd900 tool if necessary. Yes, airborne is transmitting telem constantly.
  • I have a pair of RD 900. I haven't installed it on my plane yet. My radio's shipped with 2 small ones and 2 big ones. I thought each radio got one off each is this not the case? Sorry to jump in the thread here...

    • U can do it the way u suggest but u will defeat having diversity. Ur system will always pick the higher gain antenna, the one u call the big one.
  • Hi Steven,

    I'm having range problems with my RFD900 - perhaps you can help. Could you post your settings perhaps?

    If you have the time here are details on my issue -> http://ardupilot.com/forum/viewtopic.php?f=94&t=7811&p=1740...

    • Your settings look okay but I would change the airspeed to 64. Use the tool on the RFD900 site and set to default values to be sure. http://rfdesign.com.au/downloads/

      You also realize your Tx and Rx power settings are not maxed out, which would be 30dBm. On the ground side you shouldn't have a problem but in the air you may be better off with your lower setting due to the impact on other RF sensitive devices, like the GPS Rx.

      Here is what I see as your problem. If the picture is correct or I should say if I'm seeing it correctly, your airborne antenna are going to be out of phase with the ground antenna. In fact, they would be the worst possible way to have them. The ground, which should be the longer 1/2 wave dipoles, need to be roughly vertical. The smaller 1/4 wave monopoles on the Air modem need to vertical as well. Both antennae can be in a slight V to help keep max polarity while the plane is turning. Hope it helps. If not, reset to defaults and try again.

      Also, local noise on the plane will not affect the ground receive, only the Air receive and vice versa. It's another way to check where your noise is. But from your plot, noise looks low. Change the Rx antennas to vertical...

      Downloads
      • Steven,


        Thank you for your reply, very much appreciated! I will make this change immediately.

        Should I be using both antennas on the air side? As i was searching around I see people use 1 on the air side; not clear why. 

        In the manual it says:

        They are required to be mounted on a ground plane of approx 20cm diameter

        or more to operate as intended.

         Does this mean I should be taking a 20-30cm piece of copper tape and stick it on the bottom of the airplane, with a peice of the copper tape touching the ground of the antenna?

        • You can make a ground plane but really not necessary. I would use two antennas. Sometimes you can get a strong on board signal and lock onto the side without the antenna. Of course you would then be screwed as far as getting signal from the ground RFD900.

          This is the antenna you should be using. http://store.rfdesign.com.au/antenna-900mhz-2dbi-right-angle-monopo...

          With the one you got, you will have to mount the whole unit vertically. I don't know why they don't give people a choice when purchasing. When I bought mine, long ago, I asked for the 90 degree antennas.

          Antenna 900MHz 2dBi Right Angle Monopole (RPSMA)
          RFDesign designs and manufactures the Antennas, RF Electronics and the RFD900 radio modem
          • Raph,

            I wouldn't add the ground plane until you test. You may screw up, via RF reflections, your Control Rx or Reflect VTx power in unwanted places.

            The antennas below should be fine IF they are RPSMA and made well. Some of the Chinese stuff is junk. Seppo carries high quality items.

          • awesome - I did recently order those antennas so I have these two: they look different than what you linked.

            3702934745?profile=original

            And as for the ground plane - i'm glad it doesn't make a huge difference, but in the position I am in now +  the use of "required" i'm inclined to try.. just to be sure:

            -can I put this 20cm diameter copper ground plane on the base of the wing, under where the rfd900 is mounted? or does it have to be literally under the rfd900?

            -does it matter if I physically connect the ground plane to the ground of the antenna?

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @_JonMyer: 🏎 We need your help in naming my #AWS DeepRacer Underground Track 🏎 @davidfsmith's track is going to be referred to as 𝗔𝗪𝗦 𝗗…
15 hours ago
DIY Robocars via Twitter
RT @gclue_akira: 仕事もおわったし、電脳化にとらい #マリオカートハック https://t.co/4IU90hCLgm
16 hours ago
DIY Robocars via Twitter
This is the hashtag to follow all the people in Japan who are hacking the new Nintendo Mario Kart with the real AR… https://twitter.com/i/web/status/1319281354664677376
16 hours ago
DIY Robocars via Twitter
RT @gclue_akira: @chr1sa @diyrobocars jupyter mario https://t.co/P0oHdjlCRq
16 hours ago
DIY Robocars via Twitter
RT @_JonMyer: 🚨Our 1st AWS DeepRacer Community Race is Underway on http://twitch.tv/aws 🚨 Join us to find out which member of your commu…
Tuesday
DIY Robocars via Twitter
Monday
DIY Robocars via Twitter
RT @BackyardRobotcs: After an admittedly long wait, the new Tinymovr R3.3 motor controller is now available https://tinymovr.com 🥳
Monday
DIY Robocars via Twitter
RT @_JonMyer: 🏎 1 hr left before the #AWS #DeepRacer Community 🏎 Top 5 Race tomorrow LIVE on Twitch 1st Place = $50 Amazon GC or AWS Credit…
Monday
DIY Robocars via Twitter
Oct 16
DIY Robocars via Twitter
Oct 15
DIY Robocars via Twitter
Oct 14
DIY Robocars via Twitter
RT @davidfsmith: Race virtually with The AWS DeepRacer Community Race and then join us on the track to see how your times compare on the ph…
Oct 14
DIY Robocars via Twitter
Oct 14
Hiroki Tanaka liked Hiroki Tanaka's profile
Oct 13
DIY Robocars via Twitter
RT @breadcentric: It's now!
Oct 13
DIY Robocars via Twitter
RT @SahikaGenc: Happy Prime Day! AWS DeepRacer is available at a 30% discount today! @sunilmallya #AWSDeepRacer https://www.amazon.com/AWS-DeepRacer-Fully-autonomous-developers/dp/B07JMHRKQG/ref=sr_1_5?dchild=1&keywords=deepracer&qid=1602609599&sr=8-5
Oct 13
More…