X8 lost gone what can I do now?

Well,

I have had a 3D Robotics X8 for about a month now. I have been flying it in a large field near my neighborhood. I had just got it in the air in  stabilize mode and was flying  and moving about. I decided to get it up in the air a little and got the orientation out of wack and ended up over some trees. Well in went down and I have looked until dark and can't find it. I was connected via mission planner 2.0. So is their any way that I may be able to pull the last longitude and latitude settings from it? I am going back tomorrow to continue the search. Thanks

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Time for ladybirding before flying anything over a 450 quad! Why risk an expensive X8 before being 120% able to bring someting back safely in stabilize? By the way: "This is the second major crash for no reason that I can find". I hope you know the reason for the second crash now.
    Lowering expectations a bit and continue training with an appropriate machine. You will so much more enjoy your bigger copter in the end.

  • Moderator
    Loss of orientation is a common issue for new fliers. Before you spend much more time repairing your expensive quad, I recommend a few things:
    - get a ladybird or other micro quad and practice.... Working up to the lazy-8, laps, and other practice patterns until flight is smooth and orientation changes around an ROI throughout the flight.
    - explore the simple and super simple modes
    - put your name and contact info on that bad boy
    - flying too low (over trees, such that you cannot see it) can be as big a problem as flying too high. When in doubt, gain altitude. That is, if the wind is low, and you are under the local regulated ceiling. This helps not just with orientation, but also with telemetry, control signals.
    - plan your emergency procedures. Have a plan that doesn't involve going straight to RTL. Before conducting flight ops, tune and test other modes, like alt hold, position hold, etc.

    Just some quick ideas...
  • Well,

    Thats what I did and it yielded no real info. I went out this morning with about 6 good friends and searched until I/we found it. I am now grounding this thing until I can understand fully what is going on. This is the second major crash for no reason that I can find. The last crash was due to a "possible" prop coming off. This time I have no idea because the tlog file has almost nothing on it. I am using windows 7 and APM 2.0. Once I get it working again I am not going to fly it over 30 feet and keep it in a huge field until I can feel confident at it is going to operate like it is suppose to. I am very very lucky that this thing went down and did not end up in a car windshield are something worse. I had it in an open field and like I said the orientation got off and then it went out of control. I have two other copters and this has happened to me and I have always been about to get it back in the right place. I wonder if it is possible to write new parameters into the unit? I only have what came with it from 3D robotics. Is that even needed? Anyway thanks for the reply.

    Brian 

  • Moderator
    Yes, open the log file and replay it. See the Mission Planner manual for details on log files.

    Oh, and put your contact information on your gear.
This reply was deleted.

Activity

DIY Robocars via Twitter
RT @_JonMyer: 🚨Attention DeepRacer's including #UndergroundDeepRacer🚨 Check our our LIVE stream that including @IAM_dbro Take a few moments…
Wednesday
DIY Drones via Twitter
RT @MarvelmindMaxim: Extreme precision for 60 swarming robots. #marvelmind #autonomousrobotics #robotics #swarmrobotics #rtls #ips #indoor…
Monday
DIY Drones via Twitter
RT @MarvelmindMaxim: Precise (±2cm) tracking for racing boats and autonomous boats. Works outdoor and indoor. #autonomous #AutonomousVehic…
Monday
DIY Drones via Twitter
RT @MarvelmindMaxim: Helping PixHawk folks to fly autonomous quadcopters using PX4 and ArduPilot. https://marvelmind.com/drones/ Equally suitab…
Monday
DIY Robocars via Twitter
RT @chr1sa: The @DIYRobocars @donkey_car virtual AI car race is starting in 15 minutes! Watch it live on Twitch https://www.twitch.tv/mossmann3333 htt…
Aug 1
DIY Robocars via Twitter
RT @chr1sa: Don't miss our monthly @DIYRobocars @donkey_car virtual AI car race tomorrow at 10:00am PT live on Twitch. Head-to-head racing…
Jul 31
DIY Robocars via Twitter
RT @sparkfun: Our completed tutorial on building an @NVIDIA Jetson Nano-powered @Sphero RVR gets your bot up and running via teleoperation…
Jul 30
DIY Robocars via Twitter
RT @SmallpixelCar: Freeway test https://t.co/4V5tV9lhIP
Jul 29
DIY Robocars via Twitter
Very small autonomous cars racing, thanks to an overhead camera: https://control.ee.ethz.ch/research/team-projects/autonomous-rc-car-racing.html
Jul 29
DIY Robocars via Twitter
Jul 29
DIY Robocars via Twitter
Jul 29
DIY Robocars via Twitter
RT @chr1sa: Don't miss our virtual AI car race this Saturday! Real developers + virtual cars =🏎️🏎️🏎️ Head-to-head battles with thrills, sp…
Jul 28
DIY Robocars via Twitter
Jul 27
DIY Robocars via Twitter
RT @usashirou1: Jetson nano by Isaac Kaya #jetson https://t.co/Mu1N0CyQkN
Jul 23
DIY Robocars via Twitter
RT @GPUsolution: JetRacer mady by Iflytek company #JetsonNANO #Nvidia https://t.co/MimTymIwge
Jul 23
DIY Robocars via Twitter
RT @openmvcam: I love this: Mega or Mini? Image Classification on the 1MB OpenMV Cam H7 by Ish Ot Jr. in OpenMV, Edge Impulse, Internet of…
Jul 23
More…