Hi,
I tried uploading the MAV link directoreis and the arduino IDE didnt compile.
Then I tried uploading the APM directories instead and it didnt compile too, before uploading the MAV link it did compile and everything worked well, what am I missing h
Read more…Could anyone help, I am trying to use LEDs on the open output ports..what do
I need to change in the code to achieve this???
Read more…I have a GPS chip MT3329
Firmware: AXN1.30_2278_3329_384.1151100.1_binary.bin
Voltage on-chip 3.3 volts.
Under the open sky (mobile phone at the same location without problems determines the coordinates).
Basically, the chip captures one or two satellite
I was connecting to the configurator fine but had a problem with on of the motors, I fiddled with the pwr connector with the power on and I think I hosed things. I can no longer connect to the configuration program. Any one know if I can reset or fix
Read more…I read this post in a another forum where a guy claims 50Hz is insufficient PWM cycle for accomplishing quadcopter stability. Is there a truth in this ? What is the cycle of the ArduPilot PWM outputs that control the motor ESCs?
Read more…
Hi All,
I am looking for a lightweight camera. I need to be able to digitally access the images in a live feed to transmit over a wireless link. Does anyone know of any such system in the sub 75 dollar range.
Thanks,
Julian
Read more…When I enable the GPS hold on my arducopter, if I try to ascend or descend using the throttle stick, the copter does not respond. I can manuever the copter like always, but the throttle stick has no command when GPS hold is on. In the wiki, it says w
Read more…Hi friends of the ArduCopter,
I'm happy to announce that the 
ArduPirates will be further developing the official ArduCopterNG code from now on, which we call the ArduPiratesNG code..
One advantage of joining forces with the "original" Arducopter team
Hi,
I need to slow my plane down in AUTO, apparently this is the PID value THROTTLE_P, but I can't find this anywhere.
Has it been renamed?
I can find THROTTLE_ALT_P and THROTTLE_TE_P but I'm not sure.
Any guidance appreciated. Incidently, throttle i
Read more…I have an 8' Senior Telemaster because of its High Lift Capability.
And one argument I have is with the way common RC flyer's Balance the Telemaster's CG before flight.
I seek a solution for calculating the CG that provides input for the lifting tail o
Read more…I just want the plane to follow a course at its current height.Im flying 2.7.1 with IMU and using the config tool to upload the flight plan.CheersS
Read more…Hello,
I didn't receive my Arducopter parts yet, so maybe I am asking something selfexplaining.
I started with a mikrokopter, where PH (position hold) means the copter would try to stay wherever I want to, but I still could conrol hights (or switch on
Read more…Hello,
I've had my arducopter for around two months and I still haven't managed to get it off the ground. (when I did, but I've now lost 3 props.)
My problem seems to be that when pitching the copter the motors seem slow to respond to the commands se
Read more…I am interested in learning how to program on the Arduino, I decided it would be a good time for me to get into programming micro controllers. I understand where to start with the micro controller part, there are many books out there with many tutori
Read more…
Front
Closer front view
Right side view
Is it properly placed? Our should it be looking to one of the front legs?
Read more…Hi all, i need help here.
i've just downloaded the APM code v1.0, and i've followed the tutorial to set up the Arduino IDE and load the APM code; i've uncommented the GPS_PROTOCOL line and i've set it up to GPS_PROTOCOL_NONE. Then i launch the Compile
Read more…Hi guys,i've been putting up an arductopter kit with magnetometer GPS and all loaded with an NG firmware.When i start the engines the back engine start way after the others and when I have my throttle at min and I incline it backwards the prop does n
Read more…This is for ArduCopterNG_b2.
Fixes motor arming where motors will rotate continously after having calibrated the minimum throttle throught the CLI.
I post the complete files (in a zip file) that I changed since patches do not seem to go through cleanly
Many thanks in advance for any suggestion and experience first.
Need help on the following two issues:
1. Can someone confirm with me the directions definition of ArduIMU Ver2? Accroding to the mark at the bottom, the ArduIMU Ver2 follows right-hand
Read more…