I have been following the changes taking place to the ArducopterNG code and was hoping fro a major release some time soon. There doesn't seem to be any visible activity on the Configurator so....
Hi all,
Running some tests on my APM after config and the test -> airspeed is coming back with results similar to the following. Pretty sure my Skyfun isn't doing 20km/s sat on my workbench...! Can anyone shed any light on this...? Is my airspeed sen
Read more…Yesterday again trouble happened with mine quad.
I soldered a magnetometer on the OilPAN
Then I uploaded the test code for compass to get offsets and everything was working well and I decided to load SuperStable code.
I switched off everything, in orde
I'm currently testing APM at my desk using an elevon setup. Currently, I am only using a 2 position switch, 1 position being manual, and 1 being stabilize. Dx6i default settings for plane.
When in stabilize mode, moving the APM/Shield works correctly
Read more…Hey,
will Arducopter eventually support Coaxial setups, such as the Y6 or an X8?
Because i am planning on designing my own Coaxial-Copter running on the APM-Hardware.
Regards
Daniel
I just loaded the Beta 1.01 code and went for a flight today but ran into some issues. I setup the modes to be manual, stabilize, and auto. I loaded a few way points and once in the air I put it into stabilize mode. However it took over the throttle
Read more…Hi all,
Following this thread (look at the picture) :
http://diydrones.com/forum/topics/open-pins-on-apmoilpan
I'd like to know what digital and analog pins can be used for other tasks than the original.
For example, if you don't need 8 INPUT and 8 OU
Read more…Hi all,
I saw some recommandations with powering the APM with only 2S 7.4V lipo battery through the 5V linear regulator on the Oilpan.
But I'll need a 3S 11.1V or 4S 14.8V to power my servos AND the APM.
So my question : is it possible to use that kin
Read more…Hi guys,
At my school, there have been a few senior projects related to UAVs.They were good projects except they were never completed either due thecomplexity of the project or complications along the way.
After this frustrating scenario, two friends
HAS ANYONE USED THIS ?URBI Camera Controller with Zoom.
|
|
Our small USB controller lets you control a range of Nikon or Canon digital cameras for remote controlled or automated photography. Some Canon Powershot cameras also have controllable zoom.  The |
Hello,
I have a simple question.
If I want to use a 40A or even bigger ESCs which brands would you recommend?
Thank you
Hi All,
I have stuck a ArduPilot Mega to the side of my Trex450 to see how it performs with the vibrations.
I noticed a lot of drift from the IMU, for example if I change the pitch and only the pitch I notice the IMU thinks it is rolling as well. Th
Read more…Hi all,
I'm a newbie, who's keenly following all the activity in this arena. I haven't yet got my hands dirty with HW/SW but am just excited about the possibilities autonomous flight opens up.
I'm particularly interested in applications for police-forc
Read more…After a month of struggling with trying to figure out why I had no GPS data, I discovered the following tip in the APM manual. I tried this and it solved my problem. As they say, RTFM. Thanks again to everyone who has tried to help me figure out m
Read more…Hi,
Has anyone else experienced a motor spinning up ( or a servo glitching ) whileuploading new code to the APM
I totally understand that while code is being uploaded the system is in aunknown state so i should expect the un-expected from the APM outp
i,everyone, i was thinking about use the xbee module to upload the data into the ardupilot board during flight, such as i can change the waypoint when the aircraft flying. but i use the ardupilot board, the serial port is used by the GPS. is there a
Read more…I dont understand what it does and searching on here hasnt made it any clearer.Also, where dow this fit in with other NAV PID gains?ThanksD
Read more…Hi chaps,
I am planning to add the magnetometer to my APM to provide heading information.
As a PPL holder, I am fully aware that GPS can only provide track information and as such, GPS based navigation is inefficient in anything but dead calm conditi
Read more…I am trying to calibrate my transmitter, I just bought a new one the turnigy 9x. I do the regular calibration using konfigurator everything looks great. It says it fails cause I don’t use the aux channel. All the markers stay in the center when the s
Read more…Hi Community,
Getting interested in UAVs down here in kiwi-land.
Thanks for the range of resources everybody! Have had a great look around and was just wondering on which was the best FPV/UAV platform.
All the pages point to products that are not manufa
