hii
please witch option i must to choose if i have the Ardupilot Shield V2 ..
#define XY_SENSOR_LOCATION 0 // XY Thermopiles Sensor placement
// Mounted right side up: 0 = cable in front, 1 = cable behind
// Mounted upside down:
I have a quick Newbie question.
Is there a way to hook up my Turnigy 9x to my computer to use it with a flight simulator like FMS?
If so what would I need to go about doing this?
Read more…I upload Arducopter_alpha_RC1 and then I try configure. but I get this message
I plan on getting a bachelors degree in electronics engineering, and perhaps computer science as a double. Possibly going on to get a masters in one of them. If I wanted to work on UAV design, as in the technical parts, not the design of the aircraft
Read more…I got the beta frame and used the long aluminum arms but in my first flight I moved the stick up, the copter flew really high. I panic and reverse the throttle what caused the copter to fall and broken one arm.
When we hook up a battery to the board, what LED's should light up? When attempting to load the code, what is the order in which the LED's should blink or alternate?
We are having trouble loading the code, and keep getting errors. We have a 3.3V (3
I have just purchased my first Xbee 900mhz modems to replace an older 2.4Ghz Maxstream system. I was wondering if anybody had any suggestion on optimum antennas? Also can you use a pigtail to connect between the Xbee card and the antenna without affe
Read more…I am in a group working on Paparazzi. For my 48" Delta wing airframes, I have been using the thermopiles for a while which actually prevent me from getting my project going. So I turned to low cost IMU and Ardu is the very first choice. So far I have
Read more…Hello, i just buy a 6dof imu ultra thin. Im trying to get angles with this dcm code. http://voidbot.net/razor-6dof.html
Everything works fine except the yaw. My problem is that the yaw value keep increasing even if the board isstable. Is that because
this is the worlds smallest rc plane...... it literally weighs less than a piece of paper and costs $200aus.....WOW! so what do you think
Read more…Hello All,
Hello everybody !
Prior to build my own quadcopter, I have build a GAUI330x and it was flying very well for few months.
Then, I have started to upgrade it to familiar myself with APM+oil pan boards.
This is its new configuration :
- structure/ESCs/mot
Read more…HiI would please like to know if anybody knows about a model of a quad for realflight v4.I really like the idea of a quad but not if it flies anything like a chopper. Just to darn difficult...So if anyone knows about a model or grade quad noob friend
Read more…Hi Guys,
This is my first post in this forum, but I have been reading on you progress for awhile now.
WOW! looks like you guys achieved so much with minimal HW and processing power.
A couple of month ago I finished a self balancing robot project (writ
Read more…Hey all,I recently ordered the necessary parts for the APM. I have received most part, and am only waiting for the controller board from Sparkfun.I have been looking for videos of working/flying airplanes with APM, but have only found a couple.. I ha
Read more…i am using this short program..
Servo myservo;
int pos = 0;
void setup()
{
myservo.attach(9);
}
void loop() {
incomingByte = Serial.read();
while ( incomingByte == 97 && Serial.available () == 0) //left aileron
{
myservo.write(45);
i have been working on my Future UAV,,,,,, and i have two options:
Normal V tail or inverted V tail.....:::
Hi,
Does Ardustation show any values on its screen while APM is in stabilize mode?
I'm just seeing zeroes and wondering whether I will only see values with APM in auto mode.
thanks
Read more…I have to build a Multi Functional Thermal Imaging Drone or M.F.T.I
It has to include the following telemetry hardware :
1)Speedometer
2)GPS
3)Thermal imaging camera
4)High qaulity still image camera
Other necessary must haves or be able to do.
Read more…
I have made my own power dist. board since I can not buy one and I was tired of waiting to fly! I went to RS and saw some small PCB boards and I figured I could make them work! There are 2 boards in a pack which was great in case I screwed up or in m
Read more…