All Discussions (213)

Sort by
300km

Bad GPS navigation

I did a small test mission last weekend and found the GPS navigation accuracy was quite poor. I've attached a screenshot showing the actual path taken compared to the WP path it should have followed from WPs 2 to 9. The speed was set to 5 or 6 m/s.

I

Read more…
6 Replies

DroneShare Profile Analysis

spacer.gifspacer.gif3dr Y6

Droneshare has detected parameters that are outside of the recommended range. The suspect values are marked in red - you should check on DIY Drones to figure out if you are doing a bad thing.

MOT_TCRV_MAXPCT 93 Set to the lowest pwm position tha

Read more…
0 Replies

Prop nut tightening

I have a 2013 Y6 with the old style motor collets with rounded nuts that are tightened with a 2mm hex wrench. I had a crash earlier this year when a prop flew off mid flight despite me having checked the nut tightness prior to flight. Since then I ha

Read more…
16 Replies

PDB signal wires

I have a 2013 Y6 I built from kit. I have always found the PDB board ESC signal wires to be problematic. They are quite fragile. At one stage three of them broke off at the board. I managed to solder them again but they are close together and there a

Read more…
7 Replies

Long distance mission flight

Has anyone flew long missions with their Y6? I'm planning a 3.8 mile flight mostly above straight roads, and will follow in the car.

A few questions:

1) What is the maximum advisable speed to fly for the most efficiency? I've been using 12-15 m/s.

2) Th

Read more…
14 Replies

Lifting 900g with 3DR Y6

Hi,

My first post here. I've been searching the forum for info on this, sorry if I've missed something.

I have a 3DR Y6 2013 DIY [1] that I've been flying for about a month, very happy with it so far. When I bought it I expected (naively) that I'd be

Read more…
27 Replies

Two-wire JST from PDB

I have my PDB connected to the power module via XT60. I have the APM connected to the PDB via the 6-position red and black cable.

I have an extra red and black 2-wire cable with JST connector coming from the PDB. It's not currently connected to anythi

Read more…
10 Replies

Electronic Issues

So I have 9 flights under my belt. 

First one resulted in a light crash, flip on landing, that resulted in a broken mast.  Replaced the mast and everything was perfect for flights 2 and 3.

Flights 4, 5 and 6 I found that I could not "arm" the system wi

Read more…
0 Replies

3DR FPV Issue?????

When I ordered my 2014 Y6 (fully assembled) I purchased the full OSD/FPV kit and FPV monitor from 3D Robotics.  To avoid any issues.

Have it set up where I am using the "dual" receiver on the Monitor, not the receiver that came with the kit.

 

Well, to

Read more…
5 Replies

Compass/GPS without mast?

Does anyone have any practical experience with the compass not using the mast?  Just having it sit on the top deck?  I keep breaking the mast and at $10/ea, it is not a practical part.  I'm going to do a compassmot test later tonight or tomorrow.

Read more…
32 Replies

need help with y6

I am sorta new to this whole drone thing. I have a y6 with a apm 2.6 it was a RTF kit from 3dr and i am having problems with it completely stoping my motors and it dropping out of the sky. I do have a tarot 2d gimbal and i have attached to that an ol

Read more…
12 Replies

Y6 Auto Tune question

This was probably answered, but tonight I used Auto Tune on my Y6. I noticed after doing it there is a box checked 'Lock Pitch and Roll Values'. What is that for and should it be checked?

YZ22zy2.pngAfter a few weeks of frustration and noob mistakes, I'm really

Read more…
1 Reply

(Newbie) Y6 Flight trouble

Well, the last weeks I was trying to assemble a 3D Robotics Y6, I could do it, I had to downgrade the APM to 2.9 because the I2C voltage was 5.0 volts and MP showed the message: Bad Gyro Health, but when I arm the motors they didn't work fine.

I'm not

Read more…
17 Replies

DIY Y6 Pixhawk backup power question

I have the flying down pretty good with about 2 dozen successful manual flights and missions, but one thing that's been bothering me in the build manual is this section on 'backup power'.

One the one hand it says the zener diode is best but not requir

Read more…
8 Replies