Hi,
I am a rookie and just star a drone kit and after getting all the pieces together and trying to lift it off with a Taranis remote it won't fly off. I am using the pre-multi rotor set that the remote has.
Set up:
Rotors: DJI 2312E
Wings: 9450
Receiver:
Read more…Hello people,
I would like to know how I can spin the 4 motors of my IRIS 3DR+ using a PWM wave. Although, I don't want any controller active while I'm spinning the motors, at least, not now. Afterwards, I want to use Ziegler-Nichols Method to find ot
Read more…I've got a genuine Pixhawk that I bought from 3DR that I am trying to get configured properly. I am running Mission Planner 1.3.36 and have run through the basic configuration process (compass, level, radio, ESCs), but after this when I put the prope
Read more…Hi guys, I had to reset all my parameters to default due to something getting changed while trying to get retractable landing gear installed. I've forgotten exactly what got changed, but I've gotten it mostly back to normal. Except i don't know how t
Read more…hi , im wanted to add obstacle avoidance function of the drone to pixhawk . Im using 3 sonar , however i dont know how to connect them and how to write the code to display each of the sonar value , can someone please help me ?
im using pixhawk , miss
Read more…Hi all,
I have a problem trying to override the EKF position data from an external source.
My goal is to fly a quadrotor indoor using external sensors (vicon/lidar/...) in LOITER mode.
I successfully generated fake GPS data fed to the GPS serial port. B
Read more…im doing school project , i need build a pixhawk using mission planner that have Avoidance System . I dont know how to start , can anyone help me ?
another problem i face is , when my sonar SRF 02 connect to pixhawk I2C , sonar voltage is always 0
Read more…im using mission planner and i wanted to save the SRF02 12C code into my pixhawk . However , the distance keep display the same number in mission planner . can someone please help me ?
Read more…Dear friends,
Here is a problem , may you can help me to solve:
I want to set one outupt on APM to set a servo for 3sec(for example: from 1000pwm to 2000pwm.) at waypoint.
I aslo want to control this servo from transmitter switch during auto and manual
Read more…Hi all, I'm upgrading my Ironman FY690s Hexacopter, with a set on retractable landing gear. I can't seem to get it to work. My Autopilot is running APM 2.8 it flies well, but the landing gear is a new addition. I have a Radiolink AT10 Tx paired to a
Read more…Just a friendly suggestion
I really like the Motor Test screen in clean flight
I can test my motors individually, all at once, check motor directions and calibrate my esc.
It's a great tool.
Hi , im doing my school project and i faced this problem . i need to build a copter that can avoidance obstacle using pixhawk and EZ0 . However , i have no idea how to start . im using mission planner AC3.2.1 . Can anyone please share with me ? than
Read more…hi , i have connected LiDar to pixhawk AUX OUT 5 and 6 ( follow http://ardupilot.org/copter/docs/common-rangefinder-lidarlite.html ) however , my sonar-range is un-change with LiDar is moving around . may i know how to solve this problem ? The distan
Read more…I have a quadcopter on a s500 frame with an issue that i just can't seem to figure out.
here is the parts list:
- turnigy sk3 1130kv motors
- hobbyking 20a ubec/escs
- apm v2.8
- turnigy 5200 mah 3s lipo
- hobbyking t6a v2 tx/rx
I do not have a power module
Read more…hi , i got Bad LiDAR Health error when i connect my LIDAR-Lite to pixhawk . Sonarvoltage and sonarange is always zero , distance is 0 . What shall i do to make it work ?
Read more…Hi all,
I currently have the following commands on my mission.
1) Takeoff
2) Loiter_Unlimited
3) WP
According to the article on the MAV_CMD:
The mission will not proceed past this command while in AUTO mode. In order to break out of this command you need
Read more…hi , im using pixhawk and mission planner 1.3.37. Can anyone share with me how to control the altitude using sonar ? when i switch to alt hold , my copter will keep flying up , may i know why ?
Read more…Hello everyone
I recently joined the drone fields and i've got a small issue:
My HexaCopter is not flying as it should be (the RUDDER is shifted to the ALI stick and the opposite is true)
I didnt know how to switch it back to its original location (MOD
Read more…Hello
and thank you for your great job in this community.
Today I had an unexpected crash with my quadcopter after 11 minutes flight for the second time.
With out warnings from mission planer it fell from 30 meters like as rock.
Please help me to found
Read more…Hello,
I recently purchased a Tarot 690s hexacopter , it was partially assembled (e.i the ESCs and UBEC were already soldered to the PDB). The Flight controller is an Arducopter APM 2.8 and the TX/RX combo is The RadioLink AT10 and RadioLink R10D. Th
Read more…