buenas,
estoy trabajando en un proyecto fabricando un drone elo cual consta de 8 motores t-motor u10 100kv, esc simonk 80A, px4, helices 27x8,8. y bateria de 6s de 21000mah. me gustaria que me ayudarais para saber como puedo conector la baterias tan
Read more…I am completing a rebuild / upgrade on my heavy lift Y6.
The Maxbotics Sonar was lost in a recent crash so I chose to upgrade to the Lidar Lite.
The installation is complete and the Pixhawk and Lidar Lite is reporting the range as expected.
The issue is
Read more…Anyone ever install a Sonar on Pixhawk, or where is any instructions on it ?
here is a Sonar unit at jameco;
Read more…Hoping someone can help me out here - my Pixhawk (plane) won't arm and I have not idea what the alarm sound means as it's not in the list of sounds in the Wiki. I also get the message "Bad or no terrain data" and it won't go away like it usually does
Read more…I have a motion capture system and want to send the position of the quad to the pixhawk. I've been reading a lot about this, but haven't found how I can actually achieve this. I know that, I have to connect the UART port from the odroid (5V) to the s
Read more…Hello. I'm using a pdb that accept 6S and gives voltage to Pixhawk, current/voltage sensor, 5V and 12V too.
But unfortunately i can't calibrate the voltage readings in mission planner. When i change the voltage appear an invalid number message.
Do you
Read more…Hi,
I like using the ROI feature and so far have used it with the camera in a fixed position.
Now I want the Pixhawk to control the tilt angle as described here:
http://planner.ardupilot.com/wiki/common-tarot-gimbal/
All of that working to calculate the
Read more…Hi there,
Tried searching and came up with nothing
I have a 3dr radio on telemetry 1, and I have a OSD on telemetry 2.
I just brought a Taranis, and I would like to be able to pump telemetry down the FrSky protocol.
Is there any way to re purpose another
Read more…Hi guys
I''m looking for someone who can help me with developing software for the Pixhawk.
Appreciate any help
Thanks for reading!
Roy
Read more…CyPhy is developing a hexacopter with tilted rotors, tilted but in a fixed position:
http://www.cyphyworks.com/robots/lvl1/
This enables the LVL1 to move without tilting, so it's always level.
My question is, does a Pixhawk care about the orientation of
Read more…In a week time I more or less ruined my pixhawk by unpluggin some plugs from it (see photo). First I tried to unplug the buzzer because it really makes a deafening noise. I ended up with two loose wires. Well, the result is the same (no noise) but I
Read more…Hi all,Just a simple question:Which side of the module shall be connected to battery? (Ref Image attached).A. Right connectorC. Left connectorD. Either one ( right or left)Thank you for your help.
Read more…hi! everyone!
i read in this site, to connect the pixhawk with 6s battery, many people usually use atto pilot
power module. but someone informed that the Crius power module was good without further soldering
work.
so i bought it and connected it with pix
Read more…Hi All,
I'm running a DFI-550 Flamewheel style hexacopter with a Pixhawk controller. I have just started running missions by arming the unit, flippimg to Auto on the TX, then raising the throttle stilck to take off. Works great!
Well the other day I
Hi, has anyone been able to solve the problem related to the loss of altitude while flying forward?.
I tried setting EKF ( enabling it) and it did not help.
It is also a problem only when it flies forward.
I have not tried autotune; could this be a p
Read more…Hello everyone,
I have tried for a few times to calibrate the compass and have got the message that it captures enough point for me to click ok. But as I checked in the HUD of MP, the quad is in another location in the map and not where it should be.
I
Read more…My Pixhawk telemetry shows a lot of things, but not voltage, current and % of battery used as it does in my Ardupilot piloted quad. I did the following to check this:
- it happens in mission planner, APM planner 2, tower and droidplanner (both version
Read more…Hi, I have a quad with 4008 Tiger Motors. Have tried both 14.8 and now 22.2 v batteries. It flies really good, except I noticed in some Auto Missions it losses a lot of alttitude ( in one occasion in lost all altitude, bounced in the ground, and reco
Read more…Hello everyone,
I am using ArduCopter v3.2.1. As I looked at the Flight Plan HUD screen on MP, I see the picture of the quad not in the location it should be. It might be a few feet away from where it should be, and the orientation of the quad, that i
Read more…Hello everyone,
I am using Pixhawk on a quadcopter. I had gone over all the wiki's about how to set up RTL. Flying in stabilize mode the other day to test RTL, I toggled the switch to RTL, and the quad just started to descend as if all motors had sto
Read more…