Groups

This is a test

Looking for interview participants for research on drone use in tropical forests

Hello all,My name is Ben and I am PhD researcher from the UK. To outline my work very briefly, I am conducting research into the use of drones in tropical forest conservation and ecology, with a focus on the potential socio-cultural impacts that such technologies may have on different forest stakeholders. As part of this I am interviewing various drone practitioners to gain insights into how they conduct missions/research and their perspectives on how drones are perceived by such communities.…

Read more…
0 Replies

DIY 350mm quadcopter

Hello and thank you for allow me to share my experiences with you. I am selecting my components and it's my first quadcopter. After some research I have the following components:Frame 330mm: (160g)Propellers 8045Motor 2212 1400kv (192g)ESC 30Amp Readytosky (100g)Flight Controller Naze 32 (10g)Power distribution board Blusky with XT60 (10g)Battery 11.1v 3s 30c(191g)Flysky FSi6S with iA6B After complete the same calculus in this tutorial...the flight time is 13 minutes and I think that is very…

Read more…
1 Reply · Reply by Marc LE BRET yesterday

Arduheli on 3DR Solo cube?

Can someone please confirm that Arduheli can be installed on 3DR Solo Cube without issues? Since they can be bought for cheap and are small and compact I'm looking at getting one for hobby project.Before you ask, yes, I'm aware of all the hardware issues with the cube. Used to work professionally with the stuff.

Read more…
2 Replies

Low Profile Camera Car; Concept & Advice Request

Hello all. I've been operating quadcopters (and a hexacopter!) for a couple of years now for my company, and lately I've encountered a new challenge that such vehicles are not capable of performing.I have arrays of photovoltaics that have serial numbers on the underside that I need to locate. The process of doing so manually would involve physically detaching and lifting each module, a process that would likely take many hours, if not days, depending on the site.I am conceptualizing a wheeled…

Read more…
1 Reply · Reply by Dave Coleman yesterday

Insta 360 one R ( 1" )

Hi,I am thinking on getting an insta 360 one R with the 1" mod to do some aerial photography and as bonus with the 360 mod also can create 360 footage.Does any one know if it is possible to trigger the camera with a cable remotely ? (sending some signal or short a pin to ground).i can't much info for this camera at the moment.Thanks.

Read more…
0 Replies

Automation of routine to get from the gound into hover.

I have read that some commercial multirotors have programmed routines to get off the ground and through ground effect up high enough to hover or fly.Is this real or just marketing hype? If this is really a feature, how many pilots find it useful? How different would it be that straight manual control of the throttle? Has anyone seen data regarding the difference in thrust requirements between being on the ground and successfully reaching the height that ground effect no longer affects flight?

Read more…
0 Replies

Stryker RC plane with Pixhawk Autopilot Setup

Hello,It's been awhile since I've played around with traditional helicopter and multi-copters with pixhawk. I recently got a wild hair to put the pixhawk onto a Stryker RC plane.Question:1. Does anyone have this setup or something similar? 2. Can you send me the PID values and maybe some additional input?Thank you,Sean

Read more…
0 Replies

Industrial multirotor manufacturer wanted

Hello everyone!We are updating our fleet of drones (from DJI Matrice 600) and looking for a reliable industrial multirotor supplier. Can you advise any manufacturer that fit our requirements? Do you have any good experience that you are willing to advise?Requirements:At least 2 years on the marketPayload: 1.5 - 3 kg, front-mounted payload with a possibility to look up and down (clear view for the camera)20 min flight (with the payload above)Power for payload 16-26V, 7AIdeally ready-to-flyEasy…

Read more…
5 Replies