Different Coloured Solo Shells. Painted, Purchased, ect..

Hey Folks,

while looking at different mods and parts/accessories to the Solo I came across an Alliance Wakeboard Solo which was white http://www.alliancewake.com/wake/2016-3dr-colorware-surf-expo/. After looking further into it, it seems as though the

No Video or Connection Between Solo Gimbal & GoPro Hero3+ Silver.

Hello folks,

so after a nightmarish event of dealing with 3dr, I finally received my gimbal and attempted to install it.

The installation was acceptable, I won't say it went smoothly because, that simply wouldn't be true (the wires definitely could of

Simple Solution For Extending The Range of The Solo

Hello Folks,

after running some initial tests between my solo and phantom 3 pro, I've noticed that the phantom 3 has far more range than the solo.

Does anyone have any simple solutions that have been effective at achieving greater distance with an over

Pixhawk Diagnostics Test or Hardware Test, Determining RC IN issue... Hasn't worked since purchase

Hello everybody,

So a year later and this new pixhawk I purchased still has yet to work.

Pixhawk hardware test

Hello everybody,

So a year later and this new pixhawk I purchased still has yet to work.

Pixhawk RC Not Active Please Help, Error Code "Radio Control Not Active"

Hello again,

As I've yet to get much a response on previous post regarding a pixhawk which has the error code "Radio control not active", however it is most certainly active. as I can connect a motor to the 3 pin slot on my X8R and can sing the motor

Pixhawk RC Not Active Please Help, Won't Recognize RC Signal, Motor Spins Connected Direct to X8R

Hello again,

As I've yet to get much a response on previous post regarding a pixhawk which has the error code "Radio control not active", however it is most certainly active. as I can connect a motor to the 3 pin slot on my X8R and can sing the motor

Older Versions of Arducopter firmware?

Hello folks,

My pixhawk hasn't worked since I last updated the firmware back in december (won't detect any rc signal)

So I'm looking to get the older firmware back in order to test it that will work again?

In a nutshell here is my current issue:

My Pixha

Pixhawk Won't Detect Rc Signal, Has Before, Any Thoughts?

Hello Folks,

My Pixhawk will not detect any RC signal what so ever, any thoughts? I'm using a X8R modules with a Turnigy 9XR with XJT module. I know this exact set up works because I recently bought I secondary Pixhawk (got completely fed up with the

Where to Buy Foam for an Iris+ Case in Canada? Please Help!

Hello Folks,

So I recently purchased a Hardcase for my Iris+ and Y6, but unfortunately the case did not come with any foam included, and I have absolutely no luck finding any retailer that sells foam!

Does anyone have any idea what so ever on where a p

Need Help PLEASE!!! Turnigy 9XR with Xjt to switch between X8R modules (one on Y6 other on X8)

Hello folks,

looking for a little help here, 

I've been on the search to find a proper answer and the closet I have found is upgrading the firmware on my 9XR which is not possible at the moment as I don't have a programming card for the 9XR which from

X8 (Quad x2) PDB Design Question for an X8 build.

Hello folks,

Just wondering if this method of wiring 2 quad pdb's together will be effective to work as a pdb for an X8. 

I should note that I will be wiring them without (+/-) connectors, so Esc's direct to pdb and also that I may mount the pdb's in a

Pixhawk issues & RC recognition issues...(The nightmare continues)...Please Help.

Hello Follks,

I recently ran into a reoccurring problem with my original pixhawk I purchased from a Canadian distributor, and since day 1 I have consistent RC connection issues, although I did manage to resolved the problem with a ppm encoder after ma

Please Help, Firmware Update resulting in no more RC signal? Previous to the update it worked perfectly!.

Please Help! Flashed my pixhawk with updated APM Planner (2.1.15) firmware and now can no longer receive any Transmitter signal, when it worked perfectly previous to flashing I had just done a esc calibration with no issues what so ever...Using X8R w

Please Help, Firmware Update resulting in no more RC signal? Previous to the update it worked perfectly!.

Please Help! Flashed my pixhawk with updated APM Planner (2.1.15) firmware and now can no longer receive any Transmitter signal, when it worked perfectly previous to flashing I had just done a esc calibration with no issues what so ever...Using X8R w

Switching from Y6A to Y6B, Using Apm Planner Need Help

Hello Folks,

Just switched over all my motor rotations and esc locations on the pdb for the Y6B config,

Now my question is in APM planner on OS X all I can see if the one Y6 frame type but showing the Y6A config with the rotation flip no the rear motor

Help!!! Need to know how to use maps offline in android droidplanner 2, without a windows pc.

Hi folks,

I've been doing research into learning how to access offline maps in droidplanner 2 on my new android device. 

I'm completely new to this android operating system but have gotten the hang out droidplanner 2.

My current issue is offline maps. I

Help!!! Need to know how to use maps offline in droidplanner 2, without a windows pc.

Hi folks,

I've been doing research into learning how to access offline maps in droidplanner 2 on my new android device. 

I'm completely new to this android operating system but have gotten the hang out droidplanner 2.

My current issue is offline maps. I

Cache Maps Issues with APM Planner for droidplanner2...Only creates map.qmdb which droidplanner2 won't see

Cache Maps Issues with APM Planner for droidplanner...Only creates maps.qmdb which droidplanner won't see

Apm planner caches maps using mapripper, in turn the only file i could find was a mapscache folder containing a map.qmdb file which has not work

Pre Arm Check Issue: Check FS_THR_value?

Hello Folks,

To continue my constant battle to get my Y6 going (which is literally becoming a living nightmare, that I'm beginning to regret purchasing more and more each day with all the constant problems).

So upon upgrading software I ran into many i