Pixhawk 2.1 best stable firmware ?
Hi, can anybody tell me what is the best stable Arducopter Multirotor firmware for Pixhawk 2.1 with Edison ?
Thank you
Read more…Cristian Rougier's Discussions (20)
Sort by
Barometer problem?
Hello all,
I'm flying a Tarot hexa over a forest, in a mountain region at around 3000 meters altitude
After some time flying, device start to oscillate in altitude, down , up, down up, and yesterday
crashed in a cup of a 30 meters pine ( i called
Pending or slope flying
Hello All, how are you?
I need to flight flat at 60 meters in mountain area, and comparing google altitude with reality, google Z data isn't good to trust on it.
Can anybody tell me about where can i get good Z (altitude) data to use in mission, or tel
Read more…flight plan in irregular terrain
Hello All, how are you?
I need to flight flat at 60 meters in mountain area, and comparing google altitude with reality, google Z data isn't good to trust on it.
Can anybody tell me about where can i get good Z (altitude) data to use in mission, or tel
Read more…Pending or slope flying
Hello All, how are you?
I need to flight flat at 60 meters in mountain area, and comparing google altitude with reality, google Z data isn't good to trust on it.
Can anybody tell me about where can i get good Z (altitude) data to use in mission, or tel
Read more…Best ESC for Tarot 340kv motors
Hello All, i'm working in a bigger Tarot hexa, the TL6X001, i have the Tarot 340 kv motors and
Hobbywing 40A ESC 2-6S no BEC. (pls see attached img)
After flying 20 minutes (without payload) escs are really hot , yesterday i burned one in flight and l
Read more…Calibrating power module
Hello all, how are you?
I trying to configure the power module to right set the POWER FAIL SAFE
I changed to Attopilot 180, because i have 22,000 6S battery.
Starting device, and with no arm (only showing in MP) my battery percent remaining is decreasin
Read more…Testing payload with bricks
Dears friends how are you?
I'm working in payload tests with TL6X001, i need to install sensors on it and my goal is to load between 2-3 kg, and fly acceptable 10-15 minutes missions.
Ok, my hardware is:
Frame: Tarot TL6X001 Hexacopter
Motors: 6 x FPVMO
360 Panorama with pixhawk
I'm working in panorama 360 panorama project, using a 6 x Sony a5100 and 19mm 2.8 f lens.
Anybody have experience in to shoot 6 cameras at same time using Pixhawk ? i have the cable
to shoot one camera from pix.
I assume that the exif geotag postprocess
Read more…Mission start
Hello, all, can anybody tell me how really i can start the mission?
I write a simple mission, save to disk and copter eeprom, change to auto mode
and in ACTION: MISSION_START -> Do Action.
Nothing happen.
I try arming, or changing to auto from RC, nothin
Read more…Brave sea hull
Hello all, can anybody tell me about how to build a similar hull? or any similar available on market?
I'm working in a sport fishing project, surf fishing (from coast), and i need at least 5 boat like this.
Each boat have a cost of $1200 plus 500 shi
Read more…Catamaran electronic replace
Hello all, i need to replace all custom electronics parts and motors of this catamaran, pls see attached.
Can anybody recommend me motor, esc and battery?
I really like more powerful motors, with this both chinesse motors , boat speed is 1.5 meters per
Read more…Sony A5100 trigger shutter cable
Hello All , i need to trigger the Sony A5100 from pixhawk.
Can anybody tell me what is the pinout of the USB to 3 pin cable?
Can i connect the cable directly to Pixhawk or i need some other component?
Thank you , regards!
Cristian
Read more…Lente para ortofotos
Hola a todos, me alegra mucho haber encontrado este grupo.
Estoy armando un equipo para fotografía aérea y luego rectificar y geo-referenciar osea el producto final debe ser una ortofoto.
Ya tengo el IMU y GPS para el avión y me estoy decidiendo por es
Read more…Channel 4 low output
Hello all, sorry, i need your help.
Channel 4 output is a lot of lower than others ,
Input are ok...
Can you help me to correct this? please see attached files...
Regards
Cristian
Read more…Motor spin slow than others
Hello, all , im working with APM 2.5, in X configuration, when i arm the APM, one motor (motor 4) spin slow than others 3.
When i calibrate the ESC's in automatic mode, all spin with same speed and work fine, but when
i arm the APM and test, motor 4
Motor AMP ?
Hello all again..
I need to replace ESCs for my P4 quadcopter but i dont have any info about my motor;
only say: Motors: 4pcs (1.5kg force/pc)
Anybody know how many AMP needs this motor? (Attached)
Regards
Cristian
Read more…Board and ESCs Recommendation
Hello All, i need to replace my board and ESCs for my Quadcopter.
Currently i have the boards like in attached picture but i cant do this work, motors doesnt move with
APM or without this (radio only) .
My radio TX and RX are working fine and are this
Read more…Motors dont move
Hello, i received my APM 2.5 kit few days ago.
i connected all, and all is working fine on screen, but motors doesnt move
I tried with "motors test" in CLI (Terminal) and in ESC calibration; motors doesnt move.
TX and RX radio work fine and i can see th
Read more…Hardware needed
Hello how are you..
I purchased year ago, one quadcopter (pictures below) with a 2.4 ghz manual control.
I plain to use this for aereal photography, but i need the folowing:
- GPS
- GPS based mission planning software, and return to base.
- zoom and shoot
Read more…