hello,
I currently have a Gopro black edition that i use for FPV and photography but people don't like the "bendy" photos from the Gopro.
What is the best standard digital camera with Gopro like features that will take photos using an intervalometer an
Read more…I think it would be awesome to have a simple screen on the andropilot application with the Big buttons showing each of the modes - stabilize etc along with very basic telemetry i.e voltage and altitude
the mode the copter is in is highlighted in green
Read more…hello,
i want to figure out if my 3dr voltage monitor is working correctly
I complete a test with 2 of the EXACT same 5000 mah 3s lipo batteries.
I have a cheap low voltage alarm on the battery also. I launched to about 4 metres high and engaged loiter
Read more…when i fly fpv i always fly first in stabilize to about 30 metres and then enable alt hold. Works fine and makes flying fpv easy. However sometimes the height of the quad drifts to say 10 metres high and i have to switch back to stabilize and increas
Read more…hi,
Tonight i want to test verify height on a mission. I wanted the quad to fly at 10 metres altitude so i first set this to the default altitude in the mission planner and also enabled verify altitude. Then i added 3 waypoints by clicking on the map.
Read more…hello,
i am looking for a transmitter/ receiver with voltage telemetry and as many position switches as possible
The spektrum DX8 seems to fit the bill but i have seen alot of people complaining about sudden loss of connection for no reason - this has
Read more…Hello,
I want to setup failsafe for my Futaba T6EX tranmitter. I have been following this http://copter.ardupilot.com/wiki/failsafe/#Throttle_Failsafe
When i power down the transmitter my PWM value does not drop on ch 3 so i assume that the transmitter
Read more…hello,
i have disabled the motor compass calibration data on my APM.
I have now bought a new frame and put the APM on 2 blocks of wood which raise it well above the PDM.
Now last night i flew an auto mission which worked perfect.
See Throttle Vs mag Fiel
Read more…hi,
i am using this frame - http://www.ebay.ie/itm/130876957938?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
and these props
http://store.3drobotics.com/products/apc-propeller-set-11x47-sfp-style
I would like if the arms were longer as then arms wo
Read more…on the attached log the quad failed to head for mission point number 2 so i aborted and flew it home.
Compass is working as expected and GPS had 10 satellites.
At waypoint 1 when it reached 100 metres it appears to loop around - you can see this when y
Read more…hello,
on my new 5000 mah 3s battery attached is the voltage vs throttle.
On the log attached and associated screenshot all i did was lift the quad to about a metre high and enable loiter. I have a gopro and fat shark fpv on board
is this voltage drop n
Read more…Hello,
a few weeks back i had 3.0 rc* installed and had performed the motor compass cal but my compass was off in simple mode so i reverted to a previous version (2.91b). After a cal it was working fine on 2.91 b.
Tonight i put on 3.0.1 and calibrated
Read more…Following this article and i cannot enter the measured voltage. Measuring your battery voltage and current consumption with APM. I am using the 3DR module. Image attached
Why not - is there a bug?
thanks,
Damo
Read more…hello,
is the Motor compass calibration a requirement prior to flying when upgrading to the latest firmware.
thanks
damo
Read more…IS the following cable needed when using a separate battery to power the fat shark transmitter?
IS it needed when using the same battery as my quad?
Www.firstpersonview.co.uk/psu-regulator-boards/filtered-balance-lead-power-supply
I assume the answer i
Read more…HI,
I have a goal to fly the arducopter higher than the current tallest structure 829.8 metres and record the flight. I intend on doing this on a calm day but expect winds at high alt. I do not know what speed to expect. Has anyone brought you copter
Read more…Hi,is it recommended to disable low voltage cutoff on esc's?if so should how do I disable this on my 3dr ac-004-008ThanksDamo
Read more…As I wait for the arrival of fatshark attitude I want to know if these will work well for both transmitter and receiver ?http://item.mobileweb.ebay.ie/viewitem?itemId=200924919446&cmd=VIDESCThanksDamo
Read more…Hi,I put on some new landing gear on my quad so i could take photos - The compass went off again so i re-calibrated the quad (2.9b) - this did not help much so i decided to test version 3 rc4 ( recommended this as an option last week) and performed a
Read more…