Itzik Ronen's Discussions

Differencial thrust with twin motor plane

Do the Arduplane SW support a differencial thrust for atwin motor plane?I like to connect the motors to 2 separate channels and use the motors to coordinate turns.

Started by Itzik Ronen

joystick or gamepad control - how do I set it up?

Hi

I like to control my rover (Pixhawk) using 3DR telemetry with the ground station. Can I use a joystick or gamepad on PC? I like to do it without or in parallel to Radio Controller, how do I set it up?

Can I configure it on the mission planner?

There

Started by Itzik Ronen

What is the recommended map source for prefetching and more J

I have 3 questions:

What is the recommended map source for prefetching, Google sat? Open Street maps? There is a very long list.

There is a connection between zoom level and flying level?

After fetching, can I copy the data to a deferent computer? Where

Started by Itzik Ronen

Radio calibration failed

Hi

After the "radio calibration" procedure is done I'm getting the message that channel 2,4,5 or 1.6.7…. "Failed to set channel x". Every calibration the error is in deferent channels. Only one time I didn’t get any error.

However, the channel PWM summ

Started by Itzik Ronen

Radio calibration failed

Hi

After the "radio calibration" procedure is done I'm getting the message that channel 2,4,5 or 1.6.7…. "Failed to set channel x". Every calibration the error is in deferent channels. Only one time I didn’t get any error.

However, the channel PWM summ

Started by Itzik Ronen

frozen data

Hi,

I have a new problem with the OSD, I can see all the OSD characters but it is frozen, no data changing, only the heartbeat symbol is blinking.

Any ideas?

Started by Itzik Ronen

How do I use the Fail Safe screen

Hi

Michael, you are doing a great job!!!! Thanks, I like this software a lot.

There are always new goodies in the mission planer, there is a wiki or a place that we can see what is new and how to use it?

I like to read more on the new Fail Safe screen,

Started by Itzik Ronen

PID parameters

Do you guys have the chance to tune-up the X8 for the Arduplane PIDs and parameters?

Can you share the configuration data/parameter?

Started by Itzik Ronen

navigation

Hi

I like to start with a new project “lake navigation with electrical motor boat”.

Do you guys try that? Can I expect for good navigation results with the APM2?

Thank for helping,

Itzik

Started by Itzik Ronen

How do I activate output ch’

Hi

How do I activate output ch’ (a servo) from the planner (without using CLI) for bench testing

Thanks for helping,

Itzik

Started by Itzik Ronen

Activating a servo above WP

Hi

I have a questions relating to servo setup and activating a servo (a camera trigger) when loitering at a point:

I’m practicing the following mission: I like to get to a WP, loiter 2 times. During this loitering I like to activate a servo (from lo

Started by Itzik Ronen

PID range

Hi,

Where I can get info on the PID range? What are the min/max values?

I’ve the latest version.

Thanks for helping.

Itzik

Started by Itzik Ronen

Can we save maps and use it offline?

In the field I don’t have an internet connection.

I like to downloaded the maps at home, plane the mission, do the simulation and then go out to fly, can we do that?

Thanks for helping,

Itzik

Started by Itzik Ronen

is the GPS stable?

hi

The blue led on the GPS is stable. The LED C (red) is off. Do I have GPS fix or not?

Thanks for helping

Itzik

Started by Itzik Ronen

motors are not accelerating

Hi,Didn’t fly yet.On the bench, without props, connected to the ArduCopter configurator:When I'm starting to accelerate the motors the front and rear motors are not accelerating and running like the left/right motors. If I push the throttle at ones,

Started by Itzik Ronen