Hey,
i just had my copter flying with new pros and motors. It was a littlebit twitchy, so i did autotune which workted like a charme! The copter was very very well flying. The only thing was, that there was a slight drift (really not that much...) bu
Read more…Hey,
i have a strange problem with my copter: it flies just great in stabilize mode and it stays on point pretty ok when using poshold. Now the strange thing: whenever i have it in poshold or alt hold and move the copter in any direction it will drop
Hi is there any chance to directly set the Motor RPM from within Pixhawk?
I am thinking about building a boat and not set the throttle, but direktly the desired RPM of the prop!
Any idea on that? - Is that possible?
Thanks!!!
Read more…Hi,
i just builded a new copter, with a Pixfalcon (soft v. 3.3.2 Pixhawk clone). I does very well. but one thing is not working well: Alt hold does not really hold the altitude - at least whenever the copter is moving. It is really strange. when i put
Read more…Hi,
a week ago my Copter Running a Pixhawk clone and Firmware 3.2.1 dropped out of the sky. It ran beautifully but suddenly it just fell out of the sky. I checked The Battery Life and it was not the fault.
The huge Problem now is, that i cannot read t
Read more…Hi,
i have a Problem with my quad. So the quad was flying really really good, but then i realized that i have a hardware problem (this one here: http://diydrones.com/forum/topics/pixhawk-bad-accel-health-apm-3-2-collecting-data?id=705844%3ATopic%3A185
Read more…Hi there,
this is my first Blog post here. I am writing this because i was not able to find a lot on how to add an alexmos controller to the Walkera G-3D Gimbal (other than there is a mysterious guy called "Mat Kimm" who sells "tuned" Walkera Gimbals
Read more…Hi,
i am planning to build a boat with a steering servo wich is capable of endless rotation. Is there any need for a "mid" position of the servo while driving? Or is the PID (+gyro/accel) enough to determine where to steer?
The Idea is, to rotate the p
Read more…Hi,
is it a good or a bad idea to use Autotune when EKF is enabled? Or does this not have anything to do with each other?
Thanks,
Pcace
Read more…Hi,
is it somehow possible to simulate how a boat using the ardurover firmare would behave in water including wind and waves?
Thanks for any hint!!
Read more…Hi,
is it somehow possible to simulate how a boat using the ardurover firmare would behave in water including wind and waves?
Thanks for any hint!!
Read more…Hi,
i am planning to use a APM/Pixhawk with ArduRover firmware for a solar powered boat that will go for long distances. I have some first questions and hope you guys can help me ;)
- is it possible at all to use the Ardurover code for a boat with arou
Read more…Hi,
i have some questions about flying missions with a Hexacopter using APM 2.6 with arducopter Firmware 3.2.1:
1. What happens after a mission finishes? I used an old android tablet and droidplanner 2 to create a "mission" just some waypoints... So w
Read more…Hey,
i have a Walkera G-3D Gimbal, and i am really not satisfied with the results. No way to tune PID values, and a pretty bad stabilizing...
The Mechanics are pretty ok. SO i thought about replacing the Walkera Controll unit with a 32 bit Alexmos boa
Read more…Hi,
is it possible to use the gimbal function from APM to lock on a target with a brushles gimbal?
- so that the copter itself rotates the camera whereever it is supposed to look at?
Any ideas are welcome!
Tanks a lot!
Read more…Hi,
i am just new to drones. i made a hexa, using dji e300 esc, dji 2212/920 motors, std props from dji.
as the fc i use a apm 2.6 (firmware: ArduCopter V3.2.1 (36b405fb))
Everything kind of worked out of the box as long as i fly in stabilize mode.
Wh
Read more…