wir, ein erfahrenes Team aus sehr erfahrenen Strategen, Experten und Investoren suchen einen CEO " mit Strom in den Hosen " für den Aufbau eines Start-Ups im Bereich UAV und Sports.
Als CEO an dieser 150% Stelle verfügst Du über den entsprechende Trac
Read more…got a strange behavior when i fly a programmed set of waypoints:
my Quad ( APM2 ) and MP 2.1.12 takes the waypoints one after the other, but switches ( i can see it in the screen Log ) to Loiter on the second last waypoint. The last one is just ignore
Read more…hello
is it possible that my APM2 board has bricked ?
i have a Octo Copter with standard components:
APM2 flown well and kept updating up to 2.7.1 : all well working
after updating to 2.7.3 under MP 1.2.11 can't connect anymore.
each time i repeat the up
Read more…waypoints in the table inside the Flight planner are no more displayed.
- is it a bug o a feature ?
thx a lot
Read more…Hello there
got latest Mission Planner 1.2, Hexacopter , AMP2 and 2.7 Code on it.
I can't activate the values in the Camera Gimbal Menu because they are " greyed out "
The Gimbal tilts and pans withe the servos, but in reverse way, so i need to change t
Read more…PPM to a Futaba S-Bus Receiver ?
any experience ?
thanks a lot to sshre !
Read more…Hello there
Got the original J-Drones ESC's an a strange phenomena
when i plug in the LiPO i get a beep beep beep beep ( fast around 3 beeps per second ) from my motors.
I think this means " under Voltage ". My LiPO is fully charged and after a few try'
Read more…Hello there
got 2.3 on my standard quad and it always flyes sideways. Need to hold roll stick towards extreme to hold position...
any idea ?
tanks a lot in advance
Read more…were there any changes in loitering mode ?
- since last update i can't tell loitering is working...
.. always had to switch back to manual stabilize because quad went far in any direction.
thnaks for your help !
Read more…Hello there ! need you help :-)
got 2.2b4 Version on my Quad.
All fine : take off - stable
fly a bit - and suddenly when i want to change direction :
- yaw stick movement leads to oposite reaction....
Once the quad also started turning around 120 deg.
verr
Read more…1280 APM
original Parts
hello there
i loadet brand new V2.2 quad ( multiple try )
i takes off with no problems, but does strange things when i yaw.
It always turns just in one direction...
any idea ?
Read more…Hi there
is there any manual how to put together the j-Drones GoPro 2 Axis Mount ?
thx !
Read more…helloi got XBee Explorer Regulated sku: WRL-09132from Sparkfun.until now ( spent some hours..) it was impossible for me to make the communicate.When i take the same setup with the XBee Xtreme from Jdrones my XBee's talk to eachother with no problems.
Read more…hi theresince i updated to latest and greatest ( A.C 2038 and APM Planner 1048 ) i never get GPS 3D fix anymore. Blue LED on GPS is on after 2 min. My MTK is Version 1.6????thx a lot for any help
Read more…hellogot latest APM Planner and my AC set up properly.since APM 1048 i can't connnect via XBee's anymore. i always get : System.exeption. No Mavlink Heartbeat....I took out my Xbee and testet it with X-CTU in the terminal. Everything o.kLink is up an
Read more…Hello !
when my Quad is sitting stable on ground the Altitude is swinging +/- 6 meters in the " Flight Data ". Got GPD 3D Fix.
is that normal ?
thx a lot !
due to buned out original ESC i^ve replaced with other ESC.
Is it possible that those ECS's act different from the original model making it necessary to tune PID settings ?
regards
Read more…helloi can connect via XBee : no problem entering GCS MAVlink or Sensors.no chance to get a connection in " PID tuning "- any idea ?
Read more…after a short successful flight i plugged in the USB cable to check. the motors started trembling and one motor went up in smoke and became very hot.what's wrong ?
Read more…hello
i've just samshed my Arducopter :
fliying with the latest and greatest code : everthing well.
hoovering around a bit but suddenly the Arducopter flipped to his back and crashed to the ground.....
everythin with my 2.4 GHZ rec 7 Trans is ok.
any i
Read more…