Flying quad fine until yesterday!
Compass is calibrated and working correctly!
In stabilize mode can manually yaw fine! stop manually maintaining a heading and the quad slowly yaws (turns). Obviously it also effects alt hold and loiter, to make them un
Read more…Mission Planner 1.3.16 build 1.1.5456.14788
Flightplan screen > add some waypoints > open waypoint list at bottom. Result all data boxesds squashed to left hand side!
Click the "Add Below" button and the text boxes stretch out and become readable!
Been away, just updated to latest mp, what are those shaded circles (discs) overlaid on the maps?
They are not on google maps so must be overlaid by MP!
How can I get rid of them?
Thanks...
Read more…Remains readOnly with any ch setting, relay.
Is there a problem or is the code on the to-do list?
Read more…I have a peculiar fault on the APM2.5.
Fires up ok
Can access apm via CLI
Can upload new firmware via Arduino and MP
But When connecting to mission planner, MP starts reading vars but freezes when it gets to battery_voltage!
I could understand if it didn'
Michael, Could I persuade you to add an option in Planner>config page for a fixed toolbar choice?
Pretty Please...
Read more…This is an ongoing project, but complete enough that it could be useful for anyone flying MultiCopters
Use: Exclusively for ArduPilotMega loaded with ArduCopter firmware, Mission Planner.
Explanations added where appropriate.
All Command references have
There are several commands in MP that don't function as defined although I think CONDITION_CHANGE_ALT is probably one of the worse!
If I use CONDITION_CHANGE_ALT between waypoints and enter these (apparent) valid values:
Rate cm/sec = 200
Alt = 100
Write
Guys,
Got problems connecting this new 3dr radio!
433mhz using two air modules.
Ground station 3DR module connected using 3v3 diy drones FTDI lead to W7 64bit windows laptop.
Air module connected to apm2.5 using dedicated socket on apm
Read all the forum
Had this weird one happen today!
Place wp1 near your home position, then wp2 due south, and the third one due north, a final one near home again.
Doesn't need to be north/south as long as the three wp's are in line.
See attached pic. What happened was f
Read more…Using v2.5 pcb with the dataFlash ic.
FW v2.72b
No dataFlash insert message in cli
I understood this was a fw problem corrected in this version!
Peter
Read more…Sorry if I'm out of place posting this in two forums, but I'm trying to find out if this is a Firmware or Mission Planner problem!
Have upgraded one of my quads with the version 2.5 pcb. As you know this has the on-board chip dataFlash, I had hoped th
Is it available?
Can't seem to ;locate a source zip file.
Peter
Read more…Think this is the right forum as it seems the kmz files are compiled withing FP.
Are they listed anywhere?
Read more…Can anyone please explain!
MP log dialog
"Recreate KML" button. Q: why is it termed this, Surely it creates KML, not recreates KML?
"First Person KML" button. Q: Quick explanation of what this button does(no mention in wiki)
Thanks.
Read more….
What is OF_LOITER ?
What is the difference between it and just LOITER ?
Have flown both and can't see any difference...
Read more…Guys, Hope this is the right forum! I need a bit of help getting this working:
Got the Arduino compiling and uploading the hex file to apm2 ok.
But once done (with no errors) Mission planner doesn't seem to recognise the code, Mavlink connects, HUD tu
I'm running initial flying trials with custom quad, apm2.
So far: Level good, Stabilize good, Alt hold good
Loiter works but starts with small pendulum movements which grow to huge pendulum movements, describing an arc of about 50 ft length. Slight bre
Read more…Hi, come back to this after a short break and now my ardupilot 1.4 decides to play up!
All things seem to react as expected during a complete set up procedure, until on the <modes> screen the heading text continually shows "Initialising" (instead of w
Read more…Sorry for asking this, but I've been googling most of the day...
5.8ghz band in the UK. What is the max legal power please ?
Or does anyone have a link?
Read more…