Hello all
to make it short....
2.8.1 worked fine in all modes
3.0.1 works much better in stabilize!!! (a world of difference) BUT LOITER OVERSHOOT!!!
what can be wrong considering EXACTLY SAME components location , the same apm2 quad in fact.
Hello
I have always used this ESC's, always very cold in temp, but now I did a simonk flash for my 4 escs ...they are getting hot after 3 mins i have to land because loss of power due to temp i think...
What is the reason ? i did not calibrate them, bu
Read more…Hello
I' m building a 750mm arms apm2 quad with:
*Rc timers 5010 and 17x5.5
*Esc turnigy plush 12 from hk
*4s4p panasonic 18650B inside arms (2cm alum tubes 0.5mm thick 210gr 750m2m)
total weight 1.6kg
can anyone suggest good PIDS to start with to achieve
Read more…Hi Is there any hint you can give me maybe in PID tunning to compensate for too much powerfull motors for a frame,
motors= NTM 2826 1200kv, prop 8x47 and fram DJI flamewheel
my friend cannot hover due to climb as a rocket!! on 4000 4s, do not have 3s b
Read more…Hello please I want to know reasons/problems that may exist for 2.8 default code turned off my copter initiating a missionI must admit my radio2.4 antena was loose when happened...is this related to fail safe or similar? I have all settings default.
Read more…Hello
Im using exiftool to geotag directly from terminal cli GPX generated logs, but I'm having this error, question is, is the apm GPX able to be used in this tool?
ISSUED COMMANDS :
exiftool -geotag "log.gpx" "C:\geotag\IMG_0051.jpg"
or
exiftool -geotag
Read more…Hello
I planned a simple grid with a few waypoints, all points at 80mt and last (#15) at 15mt, like this:
I have apm2.5 xquad , AC 2.8.1, motors 4006 530kv, 12*45, 4in1 esc, turnigy talon and 3x4sx4000, 35min capable hover flight time, so that 3,23
Read more…What is that RCTimer ArduFlyer V2.5 Kit Flight Controller compared to 3D robotics? it seems to be the same but much lower price, it should be a stupid question, but why do they have such low price?
Read more…Hello all, I have just bought 4 new Aeolian C2822 KV1200 motors for my 835gr xquad (APM2), but whatever motors i place in clockwise position, in my case number 4 and 2... they get too hot, but the others remain warm.... so hot that number 4 stoped sp
Read more…Hello all, why is that? i just wanted to hover to test vibrations from my new camera setup, but when decided to land, the quad mantained the motor spinning despite my 0 throtle input... then flipped and ruined two bearings in 2 of my motors :(( when
Read more…Hello
Im having micro (in duration) glitches/ flickering (micro accelerations) when fliying my new apm2 X quad, in order to identify if they are radio problems (they are not!!) , motors, vibration, PID adjustements , or the apm2 itself, I want to ask
Read more…Hello
Can anyone tell me if in APM2 (violet board), is there any place (pins or similar) in where to get Mediatek stock GPS info (nmea 9600bps?), to redirect it to custom OSD? connecting the OSD would interfere with internal GPS APM2 operaion?
thanks i
Read more…Hello all
I've made some tests with 0 wind, almost perfect 4 all mentioned modes, first tried stabilize and was great, then tried several minutes loiter , it was perfect too!! best than ever!!. then stabilize again, and then loiter a second time. Whe
Read more…Hello I have some Concerns
Flight time
Only 14mins with 5300 mah 3s, is it ok? standard for violet motors, long 28 arms, nothing else...
Unsteady flight and rool/pitch oscilations specially with some wind (yaw is perfect)
Its almost ok, but cCompared to
Read more…Hello
I went to a park, waited for gps lock, I was in stabilize 5mts from ground, and switched to loiter, my (all stock) quad did loiter for 20 seconds fine, then "suddenly went very fast in one direction like crazy!!!", I then switched as fast as I c
Read more…Hello, I'm in need to test RTL and waypoints navigation in my AC2 Xquad all stock, i can (very well under 2.0.33) loiter and "stabilize"/"simple" , what can you recommend me to do? go to another fm version? any other tips? thks
MY CONFIG:
TYPE: "QUAD
Read more…Hello
Im with AC2 2.0.33 my LOCATION = ARGENTINE, I cannot dump my logs because of this error:
what to do? thanks!!!!
Read more…
Hello
If I have (6 flight modes) using 2 radio switches, and I need to pass to a mode configured after the 3th value, we need to change "2 levers", in that case, should I do at the very same time? because I'm afraid of seting an intermediate unwanted
Read more…Hello
I'm ending the build process of an AC2 kit from jdrones, all goes 100% fine , I have loaded AC2 last firmware, setup radio with 6 position switch, calibrated magnetometer, leveled and also setup calibration for ESC... , now before any attempt to
Read more…