About

Gender

Male


Location

Montrose, CO


Please tell us a bit about your UAV interest

RC plane nuts for a while now, this UAV stuff should be interesting


Hometown:

Montrose Colorado


Activity Feed

not2fast replied to Jasfer's discussion Troubleshooting Documentation and Operation Manual in ArduPlane User Group
"If you actually find a trouble shooting manual please, share it.
Imagine, a trouble shooting manual. That would be worth ore than the FC."
Nov 10, 2016
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"It's been a long time since I got into the radio but as I recall the reason I connected on the inside is that I couldn't get the Taranis to connect through the trainer port. The 9xR did work through the trainer port but not the Taranis. Plus…"
Mar 1, 2016
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"I can't get the pictures to load. You got them though when we first started this. You PM'd me and I replied with pictures.But, it's pretty simple. On the INPUTS page 6/13 I renamed input 6 "MODE" and made the SOURCE TR1. 
On the Mixer page 6/13…"
Aug 14, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"If you set up your mixing screen like in the pictures it will work. (probably)  I should have posted those pictures here instead of in the messages part. The Arduino program sets the value of PPM-1 to a set number for each output. If it's working…"
Aug 11, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"On your back board next to the right had ribbon connector is a pattern of six solder pads. In that six pad pattern the left pad is the signal and the lower right, or second from the right is a ground. Those are coming from your trainer port. On your…"
Aug 9, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"There aren't any labels around the ribbon cable sockets? Maybe on the back side? Looks like you are going to have to get out the multi meter and find the 3.26 volts (on mine)  and a ground. those are fairly easy to find. I'll trace my signal wire…"
Aug 8, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"There should be a wire on the back cover PCB that is marked TR_PPM. That is the signal. There are also two wire positions marked Vcc and GND next to each other. That's where the 3.26 volts comes from."
Aug 7, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"I say Hmm.... I'll take my radio apart later tonight and see if we can find some common markings. Is your radio the new one? The plus or something like that? Mine is an "old" one but the PCB is probably printed with common markings. "
Aug 7, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"First off a disclaimer. I have not had to play with the Arduino coding. I've looked at it and modified it but have not written a program from scratch. I've put Stefan's code in several radios and haven't had to modify it. That's a great little piece…"
Jul 22, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"The third picture is of the bottom edge of the LCD screen. Open the radio and remove the 5 screws that hold the screen in and tip it up and you will see the pins I soldered the wires to. The picture attached here shows where the connections are on…"
Jul 22, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"I connect inside the Taranis. I sent a bunch of pictures in a reply to your PM. Let me know if you don't get them. I'm going to try to put them here too. They will do more good here than on my "comment wall", whatever that is.
The way this handles…"
Jul 22, 2015
not2fast left a comment for not2fast
"If I did another radio I would make the wire connections on the back of the radio since I have a plug anyway. Wiring under the screen is kind of tricky.
Kevin, your control panel is impressive. I don't think you can even call it a Taranis any more. …"
Jul 22, 2015
not2fast commented on Stefan Gofferje's blog post Arduino-based mode switch
"Holly smokes!! You've taken mods to a whole new level."
Jul 22, 2015
not2fast left a comment for not2fast
"this should give you what you need. Looks like DIYD allowed all the pictures. "
Jul 22, 2015
not2fast left a comment for not2fast
"IMG_0234.JPG;IMG_0249.JPG;IMG_0252.JPG;IMG_0250.JPG;IMG_0251.JPG; IMG_0183.JPG; IMG_0254.JPG"
Jul 22, 2015
not2fast left a comment for not2fast
"Sure, I have a wiring diagram somewhere. I'll get back to you tonight."
Jul 22, 2015
More…