Artem
Share

Artem's Friends

  • Airbot
  • Dmitry Prokhorov
  • Paul Atherton
  • Tim Pritts
  • Randy Bachtell
  • Grant Morphett
  • Gyrobot
  • Todd
  • Mikhail
  • Wolke
  • snowest
  • Julien Dubois
  • Nick
  • Forrest Frantz
  • Rolf Blomgren

Artem's Groups

Artem's Discussions

New power module proposition

Started this discussion. Last reply by Artem Mar 5, 2014. 7 Replies

Hi everyone! I would like to list two ideas (none novice or mine) which I hope will gain the attention of our community and result in 3dr introducing some new products and functions in the apm…Continue

Tags: halleffect, hall effect, voltage sensor, current sensor, 6s

MyFlyDream AAT and APM/Pixhawk

Started this discussion. Last reply by William Dec 11, 2019. 6 Replies

Hi, I am seriously considering building an antenna tracker. However after some research and sourcing all the various parts/bits and pricing it all together I get a really "hacked-together" looking…Continue

noob question

Started this discussion. Last reply by Artem Nov 19, 2013. 6 Replies

Hi everyone, I've just finished building a tricopter, put an apm 2.6 with external mag/gps on a self made mast very far from any interference, but close to the CG my apm is directly on the CG. done…Continue

Tags: 2.6, apm

 

Artem's Page

Latest Activity

William replied to Artem's discussion MyFlyDream AAT and APM/Pixhawk
"Brian...I just started messing with my MFD AAT.  Had it since 2016 or so and now have time to figure it all out. can you show me how you connected the M8N to the Telefly please. I have at least 3 GPS units laying around that came with…"
Dec 11, 2019
William replied to Artem's discussion MyFlyDream AAT and APM/Pixhawk
"Old post but here I am asking a question.  Did anyone succeed?  What was the solution? What about using a 3dr gps just for the telefly?"
Dec 11, 2019

Profile Information

Please tell us a bit about your UAV interest
amature
Hometown:
RF

Comment Wall (4 comments)

At 6:05pm on January 29, 2014,
MR60
Forrest Frantz
said…

What is your budget?

At 6:14pm on January 29, 2014, Artem said…

this is going to be for my "dream tricopter"  and thus I will be making some saving for this purpose, so if it is under 100usd than I think I could afford them....  so far I found NX-4006-530kv motors 67g 481g @ 3.35amp theoretically 

At 6:16pm on January 29, 2014,
MR60
Forrest Frantz
said…

Also, can I phrase the question as such:

Is there a rotor (motor and prop) that generates more than 430 grams of net thrust (500 grams less motor weight of 70 grams; thrust after the weight of the rotor is removed along with the additional weight of 2 grams per inch of prop over 10"), while sipping 43 watts or less (3 amps at a 4S voltage that varies between 10 and 17 volts)?  In other words, a rotor with an efficiency of about 10 grams per watt at 430 grams of net thrust.

Is it OK to word the question that way?  If so, then a 130 gram rotor generating 560 grams thrust at 43 watts would be OK as would a 50 gram rotor generating 480 grams of thrust at 43 watts.

At 5:33pm on June 27, 2015, Paul Atherton said…

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2020   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service