El7ias
  • Male
  • Petaluma, CA
  • United States
Share

El7ias's Friends

  • Scott Walters
  • Richard Brown

El7ias's Groups

 

El7ias's Page

Latest Activity

El7ias commented on sander's blog post DeltaQuad VTOL autonomous maiden flight
"Nice! what is your full flight weight of this build?"
Sep 5, 2018
El7ias added a discussion to the group ArduRover User Group
Thumbnail

Traxxas X-Maxx ROVER ESC advice

Hi,I have converted a Traxxas X-Maxx into a rover using the Pixhawk Cube 2 controller kit with a Here GNSS.I swapped out the original X-Maxx remote controller for an X6R receiver and Taranis QX7 radio.latest version of ArduRover firmware installed as of 8/11/18.  The rover has an EZRun Max6 ESC. The problem now is the ESC control over the transition into reverse. The ESC is currently set to it's Running Mode Option 2: "Forward/Reverse with Break", AKA the "Double Click Method".What this mode…See More
Aug 13, 2018
El7ias replied to El7ias's discussion Help! No throttle or steering response! in the group ArduRover User Group
"Hi Antonie,  Firstly I was using the PX4 flight stack and attempting to load the Rover profile through the Airframe tab in QGroundControl and was having no luck and later abandoned the PX4 firmware for ArduRover and now everything works pretty…"
Aug 13, 2018
Antonie Kruger replied to El7ias's discussion Help! No throttle or steering response! in the group ArduRover User Group
"HI El7ias This might seem like a stupid questions: 1. Did you calibrate your radio(RC transmitter) in mission planner? AP must know where the PWM starts and ends. 2. Is your signal cable from the AP to the ESC/speed controller on the right pin - did…"
Jul 1, 2018
El7ias added a discussion to the group ArduRover User Group
Thumbnail

Help! No throttle or steering response!

Hi all.I know this is an Adurover group, but Thought I would reach out and try my odds for some help as I'm perplexed by this problem. I have a Traxxas X-Maxx set up with a Pixhawk Cube 2.1 and the Here GPS. I'm using a Tarranis X7 remote controller and a X8R Sbus Receiver. I'm using QGroundControl with the latest, Pixhawk 1.8.0 Firmware with the Generic Rover airframe profile installed. As instructed, I have Steering servo wired into Main 2 and Throttle ESC wired into Main 4. Sensors are…See More
Jun 30, 2018
El7ias replied to Michal G's discussion chassis for Pixhawk-based rover in the group ArduRover User Group
"Hi all!  I have a Traxxas XMaxx 4wd with the Pixhawk Cube 2.1 and Here GPS. Using a Tarrais X7 controller w/ X8R SBus receiver. Everything is set up correctly using the latest firmware 1.8.0 using the Generic Rover configuration, Steering…"
Jun 30, 2018
El7ias posted a status
"Pixhawk Rover w/ QGC"
Jun 25, 2018

Profile Information

About Me:
UAV Prototype Engineer at Terrafugia Inc. CoDesigner of the HIRO Action Sports Drone. CoFounder Game of Drones. Robotics developer and enthusiast. Artist, builder, maker.
Please tell us a bit about your UAV interest
Land, Air, Sea and Space. Shredding the technological envelope to realize UAVs full potential benefits to best serve humanity.
Hometown:
Petaluma

Comment Wall (2 comments)

At 9:32am on March 12, 2013, Scott Walters said…

El7ias

Just put the file in a standard format (.STL, .STEP, .IGES). "I prefer .stl."

let me know the units used. Put it in the file name(MM/IN).

I don't know a link off hand. I've been 3D printing since 2005. I would just search MakerBot, or Shapeways(paid 3d printing).

Are you willing to do trading for prints, or pay for plastic and shipping?

Thanks, Scooter46290

At 8:29pm on March 19, 2013, Scott Walters said…

The printer I currently use since 2005 is a Dimension Elete. http://www.dimensionprinting.com/  ,

and I am getting a "makibot" http://makibox.com/,

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service