James Miller
  • Male
  • Nevers, Nievre
  • France
Share

James Miller's Friends

  • Todd Hill

James Miller's Groups

James Miller's Discussions

Qgroundcontrol and mission planner compatibility

Started Feb 5 0 Replies

Beginner here. TIA for patience.I've configured my pixhawk flying wing with Mission Planner, and am ready to fly when the weather breaks, but need to use a tablet in the field. I'm wheelchair bound,…Continue

Tags: launch, auto, planner, mission, qgrouncontrol

No servo movement

Started Dec 16, 2018 0 Replies

Thanks to all for all the work and patience here.Tx/Rx: Graupner MX-20, GR-24MP 1.3.6AP 3.9All was well with my first AP setup of a flying wing Falcon. GPS worked, controls moved in the correct…Continue

 

James Miller's Page

Latest Activity

James Miller replied to Victor Adrian Toledo's discussion PreArm Check Error : Gyros inconsistent in the group ArduPlane User Group
"Even though it's a while ago, I have the same problem. I got a suggestion to reboot the aircraft with no motion at all, but still this gyro thing dogs me. Advice needed here."
Feb 25
James Miller posted a discussion

Qgroundcontrol and mission planner compatibility

Beginner here. TIA for patience.I've configured my pixhawk flying wing with Mission Planner, and am ready to fly when the weather breaks, but need to use a tablet in the field. I'm wheelchair bound, so I need everything right to hand. I plan to launch in auto, bungee.Dumb question1) Is it possible to use the MP configuration- parameters, etc.- and just load qgroundcontrol on my tablet? Will the tablet be able to talk to the pixhawk via SIK radios as-is, with qgroundcontrol, or must I…See More
Feb 5
James Miller replied to Bartek Sad's discussion Bad AHRS - Pixhawk
Jan 31
James Miller posted a discussion

No servo movement

Thanks to all for all the work and patience here.Tx/Rx: Graupner MX-20, GR-24MP 1.3.6AP 3.9All was well with my first AP setup of a flying wing Falcon. GPS worked, controls moved in the correct directions, I even had the travels set.Now, nothing moves. Servos inop. Re-did all configurations including the radio page successfully, except the servo output page, where only random green bars show up.This happened a couple times, but it went away. I thought I did something wrong, and finally got it…See More
Dec 16, 2018
Nobel0 replied to James Miller's discussion Ancient southpaw needs stick mode 3 to fly fixed wing VTOL in the group ArduPlane User Group
"Hello James, I think you can just tell mission planner in the configuration controller tab that the ch1 , ch2, ch3, ch4 are the ones you want according to Mode 3, that's all. I dont know Qgroundcontrol is, but i feel it is the same as it is a…"
Apr 2, 2018
James Miller added a discussion to the group ArduPlane User Group
Thumbnail

Ancient southpaw needs stick mode 3 to fly fixed wing VTOL

I'm new to Arduplane, but I've got high-mileage left-handed reflexes, and need mode 3 to fly. But neither of the ground stations I've tried allow for that control layout. How can I configure Mission planner or Qgroundcontrol in stick mode 3?See More
Apr 2, 2018

Profile Information

About Me:
I'm an aero engineer, sailmaker and pilot, (about 3300 hours, single engine land, IFR,, seaplane and glider pilot)retired and disabled (no legs) and as of 2016 a total newbie at arduino and APM. Learning.
Please tell us a bit about your UAV interest
RC modeler since 1960 (yes, that's a 6), with a long gap to go sailing (gone 14 years), then to France. Since legs went to the trash, went back to little airplanes. Legal Resident of France.
Hometown:
Paris for 15 years, then Nevers (central France)

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service