Paul Tegler
  • Male
  • Severn, MD
  • United States
Share

Paul Tegler's Groups

Paul Tegler's Discussions

GPS Rollover week - will it make our small cheap recievers useless?

Started Mar 27 0 Replies

GPS timer info, received comes from the sats, and works on a 1,024 week cycle. That 1024 week cycle resets back to zero this year on April 6, 2019. Does anyone know if this is going to mess with our…Continue

Tags: rtk, problems, reset, cycle, pixhawk

tightening folding props?

Started Sep 15, 2017 0 Replies

sounds like a simple enough question...and some of the implications have not reared their head yet in flights to date...but a general question.... hopefully a consensus of technique....How tight do…Continue

 

Paul Tegler's Page

Latest Activity

Paul Tegler posted a discussion

GPS Rollover week - will it make our small cheap recievers useless?

GPS timer info, received comes from the sats, and works on a 1,024 week cycle. That 1024 week cycle resets back to zero this year on April 6, 2019. Does anyone know if this is going to mess with our standard small gps receivers? As mfr's are not required to have redundant timer fixes built in for this event, I'm wondering if our small UBLOX (and other) receivers will be affected.pteglerSee More
Mar 27
Paul Tegler replied to Ken Wilkins's discussion Need advice on equipment in the group Pixhawk 2 User Group
"all you need to do is look at the logs.... read the alt vs the time line. But rather than trying to measure decent 'rates' all that is really important is the final Z vib  (and x and y to a lesser degree) shock value as it hits the…"
Aug 21, 2018
Paul Tegler replied to James Mark Borgaily's discussion SWEEP Scanning Lidar
"As an early supporter (kickstarter) I bought this having fallen for the comments about their Ardupilot support/intentions. It's now 2 year later and they haven't done anything in support of the drone world rather moved on to the atuo…"
Jun 16, 2018
Paul Tegler replied to Adrian Onsen's discussion Oblique photogrammetry possible? in the group UgCS
"ooops... https://leddartech.com/modules/leddarone/ is the one I use.... 3d printed case, very light...good for about 40-60m nfi just a happy end user ptegler"
Jun 16, 2018
Paul Tegler replied to Adrian Onsen's discussion Oblique photogrammetry possible? in the group UgCS
"...I can't speak specifically to your UgCS interface control Q, but can at least suggest how to maintain your distance. to surfaces..... but it's dependant on your flight controller. At least using Pixhawk.... you can use a LEDDAR (yes…"
Jun 16, 2018
Paul Tegler replied to Norimbo's discussion Moving from Mikrokopter to Pixhawk 2.1 in the group Pixhawk2.1
"*****Is there possibility to arm and disarm motors in Pixhawk like in Mikorkopter so to start motors both sticks on transmitter to low right and to stop the motors both sticks to lower left ? yes...works the same way. ...same for the 3 2 switch…"
Feb 22, 2018
Paul Tegler commented on Simon L.'s group Pixhawk2.1
"sure can.I managed to blow out a power connector (detached from the board) reflowing didn't seem to work... replacement board (non-Edison) was also a lot cheaper just looked it up...bought mine…"
Feb 16, 2018
Paul Tegler replied to moriarty's discussion strange behaviour of pixhawk-request help to understand in the group ArduCopter User Group
"did you run the compass cal at the flight site, pre-flight??? ....or did you rely on a 'home' cal before traveling to the site... ptegler"
Jan 5, 2018
Paul Tegler replied to Andrew Challenger's discussion How to wire parallel power supplies in the group Pixhawk 2 User Group
"..nothing wrong with your concept (or diagram) until one battery craps out and shorts out (overloads) the second battery. 2 batts can be monitored via the PX2 and ground station so you can at least monitor both batts. It's common to double up…"
Dec 6, 2017
Paul Tegler posted a discussion

tightening folding props?

sounds like a simple enough question...and some of the implications have not reared their head yet in flights to date...but a general question.... hopefully a consensus of technique....How tight do people tighten their folding prop bolts? IE: do you set them real tight or leave them loose enough to straighten out on their own.with/without nylon washers in use?pteglerSee More
Sep 15, 2017

Profile Information

Please tell us a bit about your UAV interest
experimenter drone pilot .love playing with the electronics
Hometown:
Severn MD

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service