Developer
Philip
  • Male
  • Ballarat
  • Australia
Share

Philip's Friends

  • alfred koh
  • Sam Wharton
  • iSkyMaster
  • David Kim
  • Gerard Metz
  • ParkYoungju
  • Tersus GNSS
  • Vincent
  • Sirius Fuenmayor
  • David Garcia
  • Corbin Hambrick
  • siyamand moloudnejad
  • Sigitas Ciapas
  • Volta Robots
  • Mike Kelly

Philip's Groups

Philip's Discussions

Loss of control

Started this discussion. Last reply by Philip Aug 30, 2013. 3 Replies

Hi All    Had my Quad fly off yesterday, and after 6 hours of searching in the wrong spot, a call for some people across the road from the crash, helped locate it up a tree :)    Flights had been…Continue

Commercial use of Drones in Australia

Started this discussion. Last reply by Hugues May 31, 2013. 1 Reply

Hi allThis is primarily an Australian issue, but in the long term it will affect us allI took this photo in Melbourne today, and went in and asked if I could use this for professional press work.The…Continue

Tags: use, commercial, UAV, CASA

Plane crash after Motor wire failure

Started this discussion. Last reply by Philip Apr 3, 2013. 9 Replies

Hi All    I have just had my first day of successful Flying on the Bixler2 with the APM2.5+ with Firmware 2.70 on it.  Other hardware on the plane was the RFD 900 telemetry, ASI, a 9x5 prop,…Continue

X-Plane as GCS

Started this discussion. Last reply by Bill Bonney Jan 17, 2013. 6 Replies

Hi, I am wanting to run the ARDUPLANE Board in RC plane, and use the data from that via Mavlink to show the realtime flight on X-Plane. I can get the RC TX to control the X-Plane, but what I want is…Continue

 

Philip's Page

Latest Activity


Developer
Philip replied to iSkyMaster's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in the group PIXHAWK
"EDIT: 27th of April 2019: Ardupilot has now added detection, prearm checking, and inflight checking and failover to the redundant sensors. This is now in Release Copter and Release Plane. Detection of the fault has also been added to Mission…"
Apr 27

Developer
Philip replied to iSkyMaster's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in the group PIXHAWK
"Thankyou very much "
Apr 25

Developer
Philip left a comment for Philip
"I don’t visit DIYDRONES much anymore, discuss.cubepilot.org is where I’m at"
Apr 24
alfred koh left a comment for Philip
"Hi Philip, Good Day.  I'm fascinated with your custom carrier board. I really hope that I can get some tips on the development for the Eagle file for this custom board for the Pixhawk2 Cube.  Hope to hear from you…"
Apr 24
Tod Rippin left a comment for Philip
"Hi Philip, I'd like to introduce myself to you and discuss your new rendition of the pixhawk, please feel free to pm me. Thanks Tod"
Apr 24

Developer
Philip replied to iSkyMaster's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in the group PIXHAWK
"Thanks, but I would still suggest making it just the link. in a year from now, will you still be wanting to manually edit this if more information comes to light? "
Apr 24

Developer
Philip replied to iSkyMaster's discussion Urgent Grounding Notice for Cubes in the group PIXHAWK
"All 2019 cubes are grounded till further notice. "
Apr 24

Developer
Philip replied to iSkyMaster's discussion Urgent Grounding Notice for Cubes in the group PIXHAWK
"You have posted out of date information. please only post the link to the correct information. "
Apr 24

Developer
Philip commented on Gary Mortimer's blog post uAvionix, ProfiCNC, and HEX announce ADS-B IN capability for The Cube Autopilot
"Thanks Gary!"
Apr 18

Profile Information

About Me:
I am an Aircraft Engineer and RA-Pilot, though now I mainly do electronic design
Kids, wife, the normal stuff....
Please tell us a bit about your UAV interest
Developing a new flying platform,
Hometown:
Ballarat

Philip's Blog

Rise of the clones

Posted on March 20, 2014 at 8:00pm 51 Comments

Rise of the Clones (APM2.x series)

http://creativecommons.org/licenses/by-sa/3.0/…

Continue

Victorian UAS Training to open its doors in Australia

Posted on January 5, 2014 at 9:00pm 16 Comments

Posted on behalf of Victorian UAS Training.

Victorian UAS Training -Commercial partners…

Continue

FPV setup with raspberry Pi

Posted on October 8, 2013 at 9:38pm 288 Comments

After much chasing, and testing, I have found this to be an efficient way of getting low latency high quality HD video out of an Aircraft. The latency is around 0.4 seconds at worst which would be OK for an FPV with an APM doing the hard work.

I will continue to…

Continue

APM at the Australian International Airshow

Posted on March 1, 2013 at 7:00am 6 Comments

Hi all

We have had the privilege here in having the Avalon airshow every second year, this year, we had a few highlights that are of importance to this group.



1. which has been mentioned, CASA, (our FAA) have made lots of noise on helping us get Airborne, and



2. Bask industries had a stand, with the APM2.5 at Center stage. People were crowding around…

Continue

Comment Wall (3 comments)

At 9:12am on February 16, 2017, Tod Rippin said…
Hi Philip, I'd like to introduce myself to you and discuss your new rendition of the pixhawk, please feel free to pm me.
Thanks
Tod
At 6:14pm on June 5, 2018, alfred koh said…

Hi Philip, Good Day. 

I'm fascinated with your custom carrier board. I really hope that I can get some tips on the development for the Eagle file for this custom board for the Pixhawk2 Cube. 

Hope to hear from you Philip. 

Alfred. 

At 5:45pm on April 24, 2019,
Developer
Philip
said…

I don’t visit DIYDRONES much anymore, discuss.cubepilot.org is where I’m at

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service