Christian Mauch
  • Male
  • Shanghai
  • China, mainland
Share

Christian Mauch's Friends

  • Wojtek
  • Adam Hubalovsky
  • Jason K
  • Manu B
  • Guy Tzoler
  • Stephen Zidek

Christian Mauch's Groups

Christian Mauch's Discussions

Problem with Mission Planner 1.3.34 and Norton 360

Started this discussion. Last reply by Mauricio May 20, 2016. 1 Reply

After updating from 1.3.32 (worked well) to the new version 1.3.34, Mission Planner was no more able to connect to the internet... satellite data, firmware updates and software updates... etc.It was…Continue

Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM

Started this discussion. Last reply by Darshan Jain Feb 27. 116 Replies

After I had a few problems with the standard power module from 3DR and the ones from Hobbyking, like falling off resistors (overheated) and burned out BEC from voltage spikes, I finally designed my…Continue

 

Christian Mauch's Page

Latest Activity

Darshan Jain replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Thanks for the reply, I'm planning to buy a couple of power modules for making measurements of current and voltage on a DJI Matrice 100. ( Current sensor 100A/12AWG) : http://www.craftandtheoryllc.com/store/002-pl-100-sensor-board/ Along…"
Feb 27
Thomas Butler replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"@Darshain, voltage measurement of a battery is like a gas gauge; same as in your cell phone! Current draw can be used to indicate motor efficiency and if they are turning. P=I*E"
Feb 21
Darshan Jain replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hey, I'm kind of new to all of this, could someone explain to me what all would I need to measure current and voltage for my drone?"
Feb 21
Ted M replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi Christian, Thank you for developing this current sensor module, I appreciate the workmanship and design. Have you tested this module at 200 amps, and high voltage such as 12s LiPO battery or 50 Volts DC?  This reference chart shows a…"
Mar 11, 2018
Guy Tzoler replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi Got the package with the power cube, sensors and hubs all looks very very good. Is there any printer friendly version for the manuals?"
Feb 15, 2018
Christian Mauch replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Sorry, I've updated most manuals recently. The new link is: http://www.mauch-electronic.com/products-manual"
Feb 7, 2018
ADM replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi Christian, the link below doesn't work: HTTP Status 404 Requested resource not available."
Feb 7, 2018
Christian Mauch replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Just send me an email... christian.mauch@hotmail.com"
Jan 21, 2018
Guy Tzoler replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi No problem, the FC will be powered form an auxiliary battery of 8s... how can I order those modified sensors? "
Jan 20, 2018
Christian Mauch replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi Guy... to modify the PL-xxx sensors max. voltage to 150V isn't a problem. However, the max voltage of my biggest BEC's is 100V (Power-Cubes). So you would need an separate LiPo for the FC and attached equipment."
Jan 18, 2018
Guy Tzoler replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi Christian,  I am already used to put your system on my builds and they works great and accurate ... so i got a little challenge, my next build is a pretty big one ... and will use a 28s lipo main pack ... i see that the x8 hub is already…"
Jan 18, 2018
Michael replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Yes I have done it right. I will recheck what is going on now the correct values are in.  I thought I had to manually measure the current while throttle was at full.  Maybe not by how I understand the links instructions.  So it looks…"
Aug 30, 2017
Christian Mauch replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hi Michael... the setup is explained on my website: http://www.mauch-electronic.com/manual"
Aug 29, 2017
Michael replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"I have entered the info on the included paper but I am not sure how to calculate other values.  Perhaps I am not measuring it correctly.  I included my multi meter connection above.  What else are you meant to measure?  How do I…"
Aug 29, 2017
Michael replied to Christian Mauch's discussion Safety First: 100A & 200A Hall Sensor with BEC for Pixhawk / APM
"Hello Christian,  I just bought three 200A Mauch sensors and have connected one up as you showed me.  I actually emailed you about it before buying, thanks for taking time responding.  I am having trouble getting the sensor…"
Aug 29, 2017
David C Phillips left a comment for Christian Mauch
"What I needed arrived today and I ordered another Mauch bec. Regards"
Feb 27, 2017

Profile Information

Please tell us a bit about your UAV interest
I spend more time in the basement to develop new things as I spent time to enjoy flying... well I still try to balance my live.
Hometown:
Freudenstadt

Comment Wall (2 comments)

At 9:50am on February 27, 2017, David C Phillips said…
Christian, I have an extra 200A sensor module but I only have a Hobbyking 3A ubec set to 5Volts. Should that work for powering a pixhawk through the sensor module? What would the pin out be from bec to sensor module?

Regards
At 5:34pm on February 27, 2017, David C Phillips said…
What I needed arrived today and I ordered another Mauch bec.

Regards

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service