Emanuele Della Volpe
  • Male
  • Naples
  • Italy
Share
  • Blog Posts
  • Discussions (6)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Emanuele Della Volpe's Discussions

Changing PID during Mission

Started this discussion. Last reply by Andre K. Feb 19. 1 Reply

Hello everyoneI'm studying how to change PIDs in flight during a mission with Ardupilot and Mission Planner.I know the PID tuning procedure through channel 6 but I can not find any command that…Continue

Tags: Mission, PID

How to set FOLLOW FRAME YAW for the SimpleBGC32- Alexmos Gimbal through ARUPILOT wiring and configuration

Started Mar 26, 2018 0 Replies

Dear All...I'm using the gimbal ARRIS cm3000 (SimpleBCG32-Alexmos). I'm practice the wiki of ardupilot which is about gimbal connection --> (…Continue

 

Emanuele Della Volpe's Page

Latest Activity

Andre K. replied to Emanuele Della Volpe's discussion Changing PID during Mission
"Your gcs, or onboard computer can easily update the appropriate parameters. Also, for most configurations, an increased load, does not require change to PIDs to still fly well."
Feb 19
Emanuele Della Volpe posted a discussion

Changing PID during Mission

Hello everyoneI'm studying how to change PIDs in flight during a mission with Ardupilot and Mission Planner.I know the PID tuning procedure through channel 6 but I can not find any command that allows to change the PID through a switch. Imagine that the drone during the flight becomes heavier, it is necessary to change the PID to a value previously tested.I would therefore like, in flight, to make a switch that changes the PIDs and then continue the mission.does anyone know how it could be…See More
Feb 19
Emanuele Della Volpe replied to airmazingvideo.com's discussion Pixhawk with BaseCam (AlexMos) SimpleBGC Gimbal
"Dear All... I'm using the gimbal ARRIS cm3000 (SimpleBCG32-Alexmos). I'm practice the wiki of ardupilot which is about gimbal connection --> (http://ardupilot.org/copter/docs/common-simplebgc-gimbal.html#commo...). During the…"
Apr 5, 2018
Emanuele Della Volpe posted a discussion

How to set FOLLOW YAW MODE for the SimpleBGC32- Alexmos Gimbal through ARUPILOT wiring and configuration

Dear All...I'm using the gimbal ARRIS cm3000 (SimpleBCG32-Alexmos). I'm practice the wiki of ardupilot which is about gimbal connection --> (http://ardupilot.org/copter/docs/common-simplebgc-gimbal.html#common-simplebgc-gimbal).During the BaseCam SimpleBGC software setting all works fine about the frame follow mode (enabled for the yaw and disabled for the pitch and roll)…than, when i connect…See More
Mar 26, 2018
Emanuele Della Volpe replied to turdsurfer's discussion Who knows how to setup Basecam follow mode with Arducopter (Pixhawk)?
"Dear  Darrell Burkey i'm using the gimbal ARRIS cm3000 (SimpleBCG32-Alexmos). I'm practice the wiki of ardupilot which is about gimbal wiring and configuration -->…"
Mar 26, 2018
Emanuele Della Volpe replied to Rick McEwen's discussion Can CAM_TRIGG_DIST be used with a camera operated by a PWM servo signal?
"..yes DO_CAM_TRIG_DIST  works fine using picoswitch (or other relay switch), i tried your solution and i'm happy to thist... Thank's a lot for your sharing Rick McEwen. Best regards !  "
Mar 26, 2018
Emanuele Della Volpe replied to Rick McEwen's discussion Can CAM_TRIGG_DIST be used with a camera operated by a PWM servo signal?
"Hi guys, I put attention to the various stages of the problem of Rick McEwen since i would try to perform a remote shuttering. I'm trying to use gopro for the mission planner survay grid and would ask you if the picoswitch solution is…"
Jan 18, 2018
Emanuele Della Volpe commented on Patrick Duffy's blog post How to control a GoPro Camera on APM/Pixhawk with a Raspberry PI using WiFi
"Hi Patrick, thank you for providing a guide on this topic. I would like to reproduce the architecture you have illustrated in your own right using Raspberry- pixhawk -Gopro.Since I still have to buy gopro and I'm not an expert programmer, I…"
Oct 17, 2017

Profile Information

About Me:
I'm an enthusiast drone maker. I'm an aerospace engineer, i want improve my capability in order to build different kind of drones
Please tell us a bit about your UAV interest
I'm trying to build a camera-drone able to gets image by remote control
Hometown:
Naples (Italy)

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service