Guillaume Sabouraud
  • Male
  • France
Share
  • Blog Posts
  • Discussions (5)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Guillaume Sabouraud's Discussions

3DR HF to bluetooth bridging

Started this discussion. Last reply by Bart May 27, 2012. 4 Replies

Hi all,I have ordered a couple of air radios (both aire modules as I'm going with 433MHz) and would like to bridge the "long range" HF module (433MHz in my case but this is applicable to 900MHz as…Continue

Tags: bridging, bluetooth, 3DR

 

Guillaume Sabouraud's Page

Latest Activity

Bart replied to Guillaume Sabouraud's discussion 3DR HF to bluetooth bridging
"Check out http://code.google.com/p/copter-gcs/wiki/CopterLink ; Setting up is quite simple, and has been dead-reliable for me. Cheers"
May 27, 2012
Guillaume Sabouraud replied to Chad Frazer's discussion 3DR Radios for the ArduStation, is it possible?
"Chad, although I didn't build this yet, I think that it will be tricky. The 3DR radios are really point to point type, not mesh network like Xbee. You might then be right about the usage of two pairs of radios (on different network ids) to use…"
May 21, 2012
Guillaume Sabouraud replied to Chad Frazer's discussion 3DR Radios for the ArduStation, is it possible?
"Fantastic ! Thank you very much Joachim. I will then buy an ardustation, it is very cheap and will be great on the field."
May 21, 2012
Guillaume Sabouraud replied to Chad Frazer's discussion 3DR Radios for the ArduStation, is it possible?
"+1 I'm interested as well. I can hook a 3DR to a small form factor laptop but the ardustation would be a more portable and integrated solution."
May 21, 2012
Guillaume Sabouraud replied to Gérard Schumacher's discussion Getting started with 3DR Radio telemetry
"Thank you Wesley for the tip: I had the exact same problem and finally managed to connect APM Planner through the 3DR radio links after a reset."
May 15, 2012
Jake Stew replied to Guillaume Sabouraud's discussion 3DR HF to bluetooth bridging
"Good luck!  Bluetooth is notoriously problematic."
May 11, 2012
Sam Kelly replied to Guillaume Sabouraud's discussion 3DR HF to bluetooth bridging
"Hi Guillaume, your idea should be pretty easy to implement using a Sparkfun BlueSMiRF or Bluetooth Mate (which has a pinout compatible with the 3DR radios, just check your RX/TX order). -Sam"
May 11, 2012
droter replied to Guillaume Sabouraud's discussion 3DR HF to bluetooth bridging
"Is bridging the same as radio mesh?  I would like to set up a few radios over an area to create a mesh to limit the radio drops around hills and other obstacles.  Is this possible? Thanks, Matt"
May 11, 2012
Guillaume Sabouraud posted a discussion

3DR HF to bluetooth bridging

Hi all,I have ordered a couple of air radios (both aire modules as I'm going with 433MHz) and would like to bridge the "long range" HF module (433MHz in my case but this is applicable to 900MHz as well) with a bluetooth device to use the copter GCS Android ground station application. It should be pretty straightforward but has anyone tried doing this ? Tips would be welcome !I will anyhow post updates to this thread about my experiment result.See More
May 7, 2012

Profile Information

Please tell us a bit about your UAV interest
Multicopters

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service