Henny V
  • Male
  • Vic
  • Australia
Share

Henny V's Groups

Henny V's Discussions

Pixhawk Plane during a mission

Started this discussion. Last reply by Andre K. Apr 22, 2017. 1 Reply

I am in the process of build an X8 plane using Pixhawk and am wondering what happens if flying a pre planned mission and the model transitions out of RC range on the extreme boundary of the mission…Continue

Toilet Bowl effect

Started this discussion. Last reply by Calvin Mar 8, 2016. 38 Replies

I'm still very new to flying a Tarot PRO Hexacopter and APM 3.2.1 and its been fine up to now, I have about 4 hours of flying experience with out incident. I added my FPV components and was about 11…Continue

 

Henny V's Page

Latest Activity

Andre K. replied to Henny V's discussion Pixhawk Plane during a mission
"It's up to you to decide, you can configure it both ways."
Apr 22, 2017
Henny V posted a discussion

Pixhawk Plane during a mission

I am in the process of build an X8 plane using Pixhawk and am wondering what happens if flying a pre planned mission and the model transitions out of RC range on the extreme boundary of the mission space. Will the model continue to fly the mission or will it revert to RC failsafe and RTL if so programmed. I am not sure if RC failsafe over rides the mission currently being executed.HennySee More
Apr 22, 2017
Henny V replied to Gerhard Laubscher's discussion Autotune successfull on low kv Motors, heavier Quads, advice?
"I should have looked at your log earlier so I apologize, I can see you are running a 4S lipo the cutoff voltage for safety of your machine for 4S should be in the area of 14.4 but no lower than 14 volts. You reach this in the first 3.5 minutes. I…"
Apr 14, 2016
Henny V replied to Gerhard Laubscher's discussion Autotune successfull on low kv Motors, heavier Quads, advice?
"Just had a look at your Loiter fail. bin. Sorry I missed it. Your hover is around 55% so your machine is under powered. Having the Throttle mid at 40% makes the situation worse. Enter 55% into the Throttle mid setting. You could consider upgrading…"
Apr 14, 2016
Henny V replied to Gerhard Laubscher's discussion Autotune successfull on low kv Motors, heavier Quads, advice?
"Hi Steve You did not indicate what mode you were switching from before entering Alt hold and Loiter but I presume it was stabilize.  Depending on the weight of your multirotor, and the power of your motors/propellers your machine maybe over…"
Apr 14, 2016
Henny V replied to Russell Allbritain's discussion Almost a fly-away video. A few questons.
"Hi Francisco The link you mention refers to a Futaba or Spektrum radio transmitter. Its not a Wiki just a suggestion related to these two transmitters. Which transmitter are you using, Its a shame you did not see I was relating to the Taranis Plus…"
Apr 5, 2016
Henny V replied to David Kershaw's discussion Flight mode confirmation??? in the group PIXHAWK
"Hi David Can you confirm you are running Opentx on your Taranis. I have this Droneshop option on my Hex and it works just fine, however its was a bit involved in getting it to work correctly. Peter from the Droneshop has a installation video on…"
Apr 5, 2016
Henny V replied to Russell Allbritain's discussion Almost a fly-away video. A few questons.
"In the Taranis plus setting the Fail safe does not need any button pressing when using the X8R receiver, its all done in the Tx or using Open Tx. When flying a Multirotyor using RX or TX failsafe is dangerous and could lead to model fly-away etc,…"
Apr 4, 2016
Henny V replied to Gerhard Laubscher's discussion Autotune successfull on low kv Motors, heavier Quads, advice?
"Weather near perfect in Sunny Australia"
Apr 4, 2016
Henny V replied to David Kershaw's discussion Flight mode confirmation??? in the group PIXHAWK
"Hi David Yes its possible but the reported message maybe different to what you suggested. If you install the "Craft and Theory" software and cable interface not only will you have this reported messages on the Taranis screen but also with…"
Apr 4, 2016
Henny V replied to Mike's discussion Pixhawk only arms through right stick and quad keeps flipping
"Hi Mike The drift in stabilize can be caused by two factors. You need to ensure your model is balanced correctly around the COG, move the battery to achieve this. Also the gyro calibration can cause drift. place your model on a level surface and…"
Apr 3, 2016
Henny V replied to David Kershaw's discussion Flight mode confirmation??? in the group PIXHAWK
"Hi Mike Follow this link. It adds all the Telemetry functionality he needs. http://www.craftandtheoryllc.com/frsky-telemetry-cable-and-user-int..."
Apr 2, 2016
Henny V replied to Russell Allbritain's discussion Almost a fly-away video. A few questons.
"Don,t use the Taranis failsafe its a dangerous option for a multirotor. Set your Taranis TX to no pulse. When the APM senses no pulses from the RX it can select Flight controller failsafe if you have the PWM set correctly in the Mission planner FS…"
Apr 2, 2016
Henny V replied to Mike's discussion Pixhawk only arms through right stick and quad keeps flipping
"Hi Mike Go back to the start of the setup procedure. Your machine is behaving very strangely. Have you gone thru all the required setup or simply put the hardware together. You need to upload quad firmware to pixhawk before any settings. Follow the…"
Apr 2, 2016
Henny V replied to ActionDrone's discussion Pixhawk Copter "Bad Accel Health" in the group PIXHAWK
"Hi I also had the inconsistent compass warning during setup. You did not indicate if you are using an external GPS and compass, If you are it may indicate the internal Pixhawk compass and the external compass don,t agree. After much time trying to…"
Apr 2, 2016
Henny V replied to David Kershaw's discussion Flight mode confirmation??? in the group PIXHAWK
"Hi David Get ride of your current radio and purchase a Taranis Plus. The way to go. Henny"
Apr 2, 2016

Profile Information

About Me:
Had model Helicopters many yours ago and just getting back into RCM again.
Please tell us a bit about your UAV interest
This is my first Hexacopter and getting it 100% tuned is proving to be challenging
Hometown:
Melbourne

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service