Justin Peeples
  • Male
  • Forest, VA
  • United States
Share

Justin Peeples's Friends

  • Shahin
  • Simone Chiaretta

Justin Peeples's Groups

Justin Peeples's Discussions

Who is good at looking over log files?

Started Apr 12, 2015 0 Replies

Can anyone tell me what happened here? I think I uploaded enough files.. Still kinda new to looking over logs. Quad copter just fell out of the air. Heard the pixhawk reboot in flight. Continue

Pixhawk Yaw Problem during a Auto Mission

Started this discussion. Last reply by Fab. V. Nov 8, 2016. 12 Replies

Hopefully someone reading this can help me out... Runnign a Tarot 650 with pixhawk. Having some trouble with YAW during an auto mission. It wanders where ever it wants to. No matter what mode I…Continue

Tags: Mission, Planner, PX4, 650, Tarot

 

Justin Peeples's Page

Latest Activity

Fab. V. replied to Justin Peeples's discussion Pixhawk Yaw Problem during a Auto Mission
"Hello,I have the same questions thnas Chris Maier.? Did you solve your problem and how ? Rc calibration ?I have yaw drift during auto mission whreas copter seems to behave quite well in loiter mode.I'm lost. If you or anyone else have the…"
Nov 8, 2016
Chris Maier replied to Justin Peeples's discussion Pixhawk Yaw Problem during a Auto Mission
"What exactly did you do to fix this issue?  Re-calibrate the RC controller for Yaw?  Can you disable the Yaw channel for Auto mode? "
Sep 9, 2015
William Palmer replied to Justin Peeples's discussion Pixhawk Yaw Problem during a Auto Mission
"This fixed a similar issue I had where craft would often creep around from time to time during a mission. A real pain for mapping projects. Thanks for your posts. "
Aug 9, 2015
Justin Peeples replied to Justin Peeples's discussion Pixhawk Yaw Problem during a Auto Mission
"Final update: So I believe I figured out my problem. Was reading the other day about "Auto Mode" and read and had already know that Throttle, pitch, and aileron channels are disabled. But Yaw channel is still enabled so you can point the…"
Apr 23, 2015
Justin Peeples commented on Justin Peeples's album
Thumbnail

My Tarot 650

"Yes, use the E800. The difference in thrust compared to the E600 is 2000grams. A nice difference. And well worth the 19 extra dollars. My AUW is 4lbs 4 ounces. And get almost 25min of hover and around 20min of camera flying time. So puttsing around.…"
Apr 23, 2015
Justin Peeples replied to Richard Kennedy's discussion No right yaw after 3.2 firmware install in the group PIXHAWK
"Point your AC in loiter mode then use the "Point camera here" or "Guided" mode to see if it points towards the wav point. Make sure you make your selection off the right hand wide of the AC so it will have to turn right."
Apr 23, 2015
Justin Peeples replied to Phil Horner's discussion Setting throttle failsafe with EZUHF and Taranis Please help. in the group PIXHAWK
"You can't set a faisafe without the TX being on. The min ppm is 991. Across all channels. Never seen anything lower. On my external EZuhf or my JR Module EZuhf. Just the way it is. I set the fail safe first, then adjusted all the channels to…"
Apr 21, 2015
Justin Peeples replied to Phil Horner's discussion Setting throttle failsafe with EZUHF and Taranis Please help. in the group PIXHAWK
"The bottom of my throttle is 991. Won't go any lower. With sub trim or throttle time. The only thing I can do is go up. My range is 991-1996. What I ended up doing, running a 9xr pro, ezuhf, and openg TX BTW, is going into offsets and raising…"
Apr 21, 2015
Justin Peeples replied to Phil Horner's discussion Setting throttle failsafe with EZUHF and Taranis Please help. in the group PIXHAWK
"I have a issue with this also. But my problem is. When my throttle is in its lowest posistion its 991ppm. When I turn it off or go full trim down I cant get it to go any lower. So I can setup a throttle failsafe? Any ideas? I have temporaily been…"
Apr 21, 2015
Justin Peeples replied to Innokentiy Antipin's discussion Pixhawk reboot in Auto
"Thanks for the reply, and no the only thing plugged into the rails on my pixhawk is the ppm input and four escs. the gimbal is powered from a 12v BEC back at the battery, and the gimbal signal wires are plugged directly into my RX. Just posted some…"
Apr 19, 2015
Justin Peeples replied to Innokentiy Antipin's discussion Pixhawk reboot in Auto
Apr 19, 2015
Justin Peeples replied to Innokentiy Antipin's discussion Pixhawk reboot in Auto
"I have excellent solder joints, heat shrink, no loose wires, and fiver power supplies going to the pixhawk. The 3dr power module, and four ESC. :-/ I don't think this was the problem. Although it would make me kick myself that was the problem…"
Apr 19, 2015
Justin Peeples replied to Innokentiy Antipin's discussion Pixhawk reboot in Auto
"This happened to me I believe the other day. 650 Size quad. 100 feet up, full gimbal setup. Destroyed almost everything. Has anyone come up with any leads? "
Apr 19, 2015
Justin Peeples replied to Fabian's discussion Automatic Landing Gear
"Did you ever get this straitened out? Just bought a new quad frame that has built in retracts and would love to be able to get this working. "
Apr 19, 2015
Justin Peeples posted a discussion

Who is good at looking over log files?

Can anyone tell me what happened here? I think I uploaded enough files.. Still kinda new to looking over logs. Quad copter just fell out of the air. Heard the pixhawk reboot in flight. See More
Apr 12, 2015
Jack Steven commented on Justin Peeples's album
Thumbnail

My Tarot 650

"Wow,nice copter justin:) actually I wanna to know how long can it fly & its take off mass Because I also planing to build a Tarot 650 and may use E800"
Apr 11, 2015

Profile Information

About Me:
Read my Google+ Post
Please tell us a bit about your UAV interest
Quads
Hometown:
Floral City, Florida

Justin Peeples's Photos

  • Add Photos
  • View All

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service