paul
  • Male
  • Provo, UT
  • United States
Share
  • Blog Posts
  • Discussions (6)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Paul's Friends

  • Doug Weibel

paul's Discussions

Pixhawk 2.1 and Futaba R7008SB RX

Started this discussion. Last reply by Jon Turner Feb 13. 2 Replies

Hey Everyone,I'm just looking for some help on a problem I recently stumbled upon. I have been using a Pixhawk 1 with ArduCopter v3.3.3 and a Futaba R7008SB RC receiver for some time now with no…Continue

Tags: calibrator, R7008SB, Futaba, Pixhawk

Updated Arduino MAVLink Tutorial

Started May 4, 2016 0 Replies

Does anyone know of any recent Arduino MAVLink tutorials?I would like to use an Arduino connected to the PixHawk to update waypoints, check current positions, etc. All the tutorials I could find…Continue

Tags: mavlink, arduino

 

paul's Page

Latest Activity

Jon Turner replied to paul's discussion Pixhawk 2.1 and Futaba R7008SB RX
"Paul, Thats an sbus rx, right? plug into the sbus port. Ive been using a spektrum satellite rx on my PH2.1 with no problems. Range may be an issue though.      -Jon"
Feb 13
paul replied to paul's discussion Pixhawk 2.1 and Futaba R7008SB RX
"Here's an update. I scrounged up a Spektrum satellite receiver and it works without a hitch. It definitely seems to me like the Futaba receiver isn't supported by the Pixhawk 2.1 and the newer firmwares. Can anyone help me confirm…"
Jul 3, 2017
paul posted a discussion

Pixhawk 2.1 and Futaba R7008SB RX

Hey Everyone,I'm just looking for some help on a problem I recently stumbled upon. I have been using a Pixhawk 1 with ArduCopter v3.3.3 and a Futaba R7008SB RC receiver for some time now with no issues.I recently purchased a Pixhawk 2.1 and have not been successful configuring it for flight yet because I cannot perform an RC radio calibration with the R7008SB. I have tried AC v3.4.2, 3.4.5, and 3.4.6. When I open the radio calibrator in mission planner (I have tried Mission Planner v1.3.36 and…See More
Jul 3, 2017
paul replied to kurt's discussion Pixhawk with S1000 wiring diagram question
"You just need to swap all the CW arms for CCW arms and vice versa. We just did this last week, flashed the Pixhawk with the octocopter firmware, and was up and running! Good luck!"
May 20, 2016
paul posted a discussion

Updated Arduino MAVLink

Does anyone know of any recent Arduino MAVLink tutorials?I would like to use an Arduino connected to the PixHawk to update waypoints, check current positions, etc. All the tutorials I could find (most rooting back to http://qgroundcontrol.org/dev/mavlink_arduino_integration_tutorial) seem to be outdated. When I follow these instructions the sketch doesn't compile.Is anyone currently doing something like this that…See More
May 4, 2016
paul replied to vincent's discussion Failed to make sitl (software in the loop) on Windows
"Replacing all call to isnan and isinf with std::isnan and std::isinf seems to put a band-aid on it... http://www.ahowto.net/mt_rand/cygwin-failed-to-build-ardupilot-because-of-isnan-isinf/"
Apr 29, 2016
paul replied to vincent's discussion Failed to make sitl (software in the loop) on Windows
"I'm in the same boat. Just wanted to comment to show some activity on this."
Apr 29, 2016

Profile Information

About Me:
Master's student at Brigham Young University
Please tell us a bit about your UAV interest
Interested in integrating and developing technologies to create robust navigation solutions for unmanned aircraft. I am especially interested in exploring methods of robust pose graph SLAM optimization to compensate for degraded GPS measurements.
Hometown:
Livermore, CA

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2018   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service