Steve Bramah
  • Male
  • Manchester
  • United Kingdom
Share

Steve Bramah's Groups

Steve Bramah's Discussions

PMW's on mission planner

Started this discussion. Last reply by Mike Kelly Sep 12, 2016. 1 Reply

I might be overstretching my abilities here, but when you put your transmitter through the calibration stage on mission planner, the PMW's seem to be fairly standard, i.e around 1100 at the bottom,…Continue

 

Steve Bramah's Page

Latest Activity

Lito P replied to Steve Bramah's discussion getting an aux output from pixhawk to gimbal in the group PIXHAWK
"I ran into a similar problem trying to hook my arducopter build into a Feiyu Mini 3D  You need to be running release 3.3 to get the extra support for channels 9-12.  That frees you up to use SBUS or any 12 channel rx. If you don't…"
Nov 17, 2016
Muhammad Abdul Hadi replied to Steve Bramah's discussion getting an aux output from pixhawk to gimbal in the group PIXHAWK
"Good luck, I too am following to know more :-)"
Nov 15, 2016
JMagnuson replied to Steve Bramah's discussion getting an aux output from pixhawk to gimbal in the group PIXHAWK
"Steve ... I wish I could help. On mine I went directly to the receiver on a couple Aux outputs to control the gimbals yaw and roll. The gimbal I'm using happens to be the Tarot T 2D.  I'm interested in your question though…"
Nov 13, 2016
Steve Bramah added a discussion to the group PIXHAWK
Thumbnail

getting an aux output from pixhawk to gimbal

Hi, I'm trying to get a pixhawk to control a gimbal, but i can't figure out how to get an auxilliary output fom the pixhawk, controlled by a DX9! anyone got a clue?See More
Nov 12, 2016
Steve Bramah posted a status
"An H.A.L with a Pixhawk controller, TurnigyD2836/9 motors, 2 axis gimbal, Turnigy GoPro look alike camera and DSM2 sat receiver."
Oct 31, 2016
Steve Bramah posted a status
"Can anyone verify that Turnigy 30a /Multistar32 ESC'S work with pixhawk, and if they do, can someone give a link as to ESC calibration."
Oct 31, 2016
dimitris arampatzis replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"I solve the problem Paul i did download the 3dr config tool and i made a local firmware update but that dident help At the past i have change the value  TELEMETRY_DEALY from 0 tgat was in stock to 10 and everything worked very good For no…"
Oct 6, 2016
dimitris arampatzis replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"Thank you paul"
Oct 6, 2016
Paul Meier replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
Oct 6, 2016
dimitris arampatzis replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"I check them with mission planner and both radios has the same values About the 3dr radio app what should i check for?l Should i reupload the firmware?"
Oct 6, 2016
Paul Meier replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"have you tried to check the radios with the MO 3DR radio app ? Maybe one of your radio has problems"
Oct 6, 2016
dimitris arampatzis replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"The antenna and the tellemetry ar away from esc or other rf noise. It worked ok before but suddenly it couldnt update home location amd cant saw the tellemetry rssi I believe its more a software problem than a hardware problem I have format sd but…"
Oct 6, 2016
David L. replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"Keep your 3DR radio telemetry module especially the antenna away from RF noisy components.  It happens to me a lot until i place the 3dr module away from high RF interference component such as ESC, motor, power module, pdb and high voltage area."
Sep 19, 2016
dimitris arampatzis replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"I wiil format the sd card and if this dosent solve the problem i m going to reload the firmware Thank you very much Paul"
Sep 14, 2016
Paul Meier replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"Dimitris, maybe its the sd card, if all else fails try reload the firmware"
Sep 14, 2016
dimitris arampatzis replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"If you have any suggest please tell me I want to thank you for your time"
Sep 14, 2016

Profile Information

About Me:
Electrician (self employed). Played with Helicopters for about 3 years. Now own a Sky Hero Anakin that i have totally rebuilt to accomodate Pixhawk.
Please tell us a bit about your UAV interest
I have a Sky Hero Anakin, fitted with a Pixhawk flight controller, so there is nothing left of the original electonics. Having a few problems, mainly with telemetry and ESC calibration.
Hometown:
Radcliffe, Manchester, UK

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2018   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service