stubugs
  • Male
  • derby
  • United Kingdom
Share

Stubugs's Friends

  • Paulo uk
  • Brian Mahan
  • Ken Gaines
  • leonardthall
  • Dave C
  • tshado

stubugs's Groups

stubugs's Discussions

apm 3.1 stabalize shoots into sky from hover

Started this discussion. Last reply by stubugs Dec 26, 2013. 2 Replies

hi has any one had there quad copter 3.1 shoot into the air from hover as ive had this happen to 2 different quads both apm2.5 vibration levels below + - 2  /9 sats hop below 1.6 as shown with…Continue

 

stubugs's Page

Latest Activity

stubugs replied to Randy's discussion Copter-3.3 beta testing
"Hi I us the gimble channel and rc 7 to make my landing gear go up and down Stuart"
Dec 15, 2015
stubugs replied to Dmitry Prokhorov's discussion Solution proposal for PixHawk IMU2-related BAD ACCEL HEALTH
"Hi would the software fix make the hardware fix unnecessary? Stuart"
Dec 13, 2015
stubugs replied to Dmitry Prokhorov's discussion Solution proposal for PixHawk IMU2-related BAD ACCEL HEALTH
"hi  do you mean put a 1k resistor across  + and - where escs plug in  or where camera gimble plugs in /aux out ? cheers stuart"
Dec 8, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Hi Plugged mine in in the house about 20 deg went outside armed and flew then after a few mins would not hold position as it was 0degs started to slop off so I think gyros or accelerometers didn't like temp change Reconnected power outside and…"
Nov 30, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"I have a mini apm 250quad v3.2.1 throttle max is there but on my pixhawk v3.3.2 no throttle max on my quad or hex but both fly fine have you calibrated your escs just a thought Stuart"
Nov 23, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Hi I us a Ublox NEO-M8N as my main gps which gets 15 sats in my living room and a second 3dr gps which is still thinking about getting a lock in the house with gps auto switch on it never actually switches gps but 3dr one is there should the m8one…"
Nov 23, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Hi did you manage to look at my log Stu"
Nov 12, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Hi I used to have two 3dr gps but it kept jumping say a couple of meters so I fitted a m8n which gets between 16 and 18 sats so there is no jump as the 3dr only gets 11 at most but should the m8n fail it hopefully will switch to the 3dr one and at…"
Nov 12, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"hi please find attached log many thanks stuart"
Nov 9, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Thanks I thought it might be on limits of the motor and props don't really want to go any more power or I'd loose flight time Stuart"
Nov 9, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"My setup"
Nov 8, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"vibration levels abit high but there was a 23mph gust winds  vibration within normal levels on not so windy days stu"
Nov 8, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"hi please find attached log many thanks stuart"
Nov 8, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Will do but hopefully tomoz as is 11.10at night here lol so if it's not raining I'll try tomorrow cheers stuart"
Nov 7, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Oh sorry no I only covered with cling film over the top to stop wind blowing in directly it was no where near air tight or all around I still got height reading on mission planer Cheers stuart"
Nov 7, 2015
stubugs replied to Randy's discussion Copter-3.3 beta testing
"Hi yes there is dense foam over the barometer in the pixhawk case Stuart"
Nov 7, 2015

Profile Information

About Me:
well into rc
Please tell us a bit about your UAV interest
just getting into it trying to get my new stuff working
Hometown:
derby

Comment Wall (3 comments)

At 10:20am on April 9, 2014, Ken Gaines said…

I am in the US (State of Louisiana)

At 12:28pm on April 9, 2014, stubugs said…

well im looking for about £1400 plus postage

it has a naza v2 iosd 2axis gimble 2no 6000 6s nano lipos

it will take a full size slr camera 15" carbon props fatshark 5.8 trans 600 mw

motors esc receiver  etc just needs transmitter

cheers stuart

At 1:34am on April 16, 2015, Paulo uk said…

Hi Stuart, Thanks for your help. I ended up buying hobby wing x rotor escs which cured the issue straight away!

Thanks again.

P

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service