Discussion group for ArduCopter users

3180 Members
Join Us!

You need to be a member of diydrones to add comments!

Join diydrones

Comments are closed.

Comments

  • This is what I used before 3DR started making the PM.

    http://m.ebay.com/itm/121306216091

    Check your LHS.

    Mike
  • @dr0n3droid Thank you for the speedy response.
    Would you be kind to show me/us a link to one of those kind of regulators? Just as as an example. Perhaps it might be simpler to get one than I though.

    Thank you again in advance.

  • @António

    Attopilot is for measurement only. What's missing is a voltage regulator to give you +5v for APM.
  • Can a Attopilot fully substitute a power module in giving power to an APM 2.5 and sending voltage and current readings to be sent by the telemetry? If not, what part is missing to make it complete? THanks

  • Surely had some stored waypoints and pulsastes the auto mode or you accidentally put the throttle and reverse mode

  • please any one help me...  i have arducopter 2.6 and motors 919 rpm 4s and i use battery 6s 4200 mah ....And I cant use joystic on mission planner and i have telemetry 915 Mhz (TX,RX) ......any one can help me in solve this problem?????

  • Does anyone here use VTails with the APM?

  • i have only one small request for every one, may i get C language programe code for the KKmulticopter V4 circuit provided by Jean-Louis. i will be very thankfull.......please help me.

  • ANyone Know how to make 2 APM2.6 working together 1 as master and another one for back up (Slave mode). I want to make redudancy 

    Reards

    LM Arwin 

  • Anyone know where to buy compatible bullet/banana connectors for the 3DR copters?  I need to replace a motor and want to use the connectors that come with the blue motor.  This appears to be a 3.5 mm banana style plug, but not sure which exact female plug would be compatible - many of the images I see online appear to be squatter than what comes on the ESC.

This reply was deleted.

Drone flying to non visible point

Hi there,I encountered a problem, while flying in auto mode, with approching to point that was not set by trajectory and is not visible after downloading mission from flight controller by Mission Planner. Does anybody encountered similar problem. The situation is that in the middle flight I stopped the UAV and uploaded new mission and after changing to auto mode it starts to fly in some direction. It goes straight to some point, so I assume it's not mechanical problem. I attached the link to…

Read more…
0 Replies

TAKEOFF WITHOUT USING GPS

Hi,Im working on a autonomous drones and im using JETSON NANO and flight controller PIXHAWK .Im able to control my drone by giving rc commands on the MAVLINK terminal itself by connecting it with PIXHAWK but now i want a python code from which i can do some operations like:takeoff,left ,right,forward,backward…and i am not using GPS…Can anyone please help me…

Read more…
1 Reply · Reply by tellinglean Oct 17, 2022

HELP quadcopter: one motor twitching and stuttering

Hello guys,I have a problem with one motor, do not spin and making a sound (videos in attachment), I changed the motor to another ESC and is work, so I checked the connections on ESC and all connections looking great. any ideas or something I can do, iam trying to build YMFC32 Brokking .thank youhttps://youtu.be/LagBqwGbixkhttps://youtu.be/PU20nCxApcs

Read more…
0 Replies

Will AHRS_ORIENTATION=8 for Arducopter 3.2.1 on APM 2.5 using a traditional Heli

I have been Reading Chris Olsen posts and watching his videos on Arducopter with traditional Helis using a Pixhawk.I have inherited an older Trex 450 heli with the old Align 3G FBL hardware.  The FBL controller appears to be bad.  So I have an old APM 2.5 without a compass or GPS on board.  I just want to replace the failed Align 3G FBL system with the APM.Now I have to mount the APM under the skids on the heli so the APM will be upside down.I have Two questions.1)  Is the AHRS_ORIENTATION=8…

Read more…
0 Replies