Gender
Male
About
Location
Patras
About Me:
Programing, UAV designing, electronic designing.
Please tell us a bit about your UAV interest
electronic, software, develope ;-)
Hometown:
Patras
Activity Feed
"SOOOOOO we are still hard working and soon YOU WILL FINALY know whats mean WOD !!!!!!!!!! :-)"
"metal is not alltime better. Its same like in plastic case, all time depend on quality of parts and assembling.
Plastic on right place absorbate lot of vibrations etc .... each solution have some - and some + ;-)"
Plastic on right place absorbate lot of vibrations etc .... each solution have some - and some + ;-)"
"if you want watch my pages DROEN SOLUTION LTD on facebook ;-)
Im autor of 3d printers DS EVIL FORGE and DS GREEN DRGON.
All my drones are printed on those printers ;-)
Resolution 3 microns ( 333 steps/mm !!! ) ;-) and speed up to 200mm/s
printable…"
Im autor of 3d printers DS EVIL FORGE and DS GREEN DRGON.
All my drones are printed on those printers ;-)
Resolution 3 microns ( 333 steps/mm !!! ) ;-) and speed up to 200mm/s
printable…"
"so bill i made thread there
http://discuss.ardupilot.org/t/wod-gsc-guided-commands-ack-3/10146
pls help or i will go to crazzy from this ..... ;-)"
http://discuss.ardupilot.org/t/wod-gsc-guided-commands-ack-3/10146
pls help or i will go to crazzy from this ..... ;-)"
"i testing it now on CMD 221 , i think its simple message ( target sysid 1, target comp 1 )
in finalizing message im using sys id 255 ( gcs) and 0 for comp
STILL SAME RESULT ...... error 3 :(
do you want me make thread on…"
in finalizing message im using sys id 255 ( gcs) and 0 for comp
STILL SAME RESULT ...... error 3 :(
do you want me make thread on…"
"bill need guided commands some special sysID or comp ID ? or they supost to work in broadcasting (0,0) ?"
"bill i was check it before , andd python is realy not my strong skill :D i write my soft in C++.
But stil what i saw there ( first link ) im doing all right :( so was not help me
if you have idea what im DOING WRONG PRECISELY ;-) i will it realy…"
But stil what i saw there ( first link ) im doing all right :( so was not help me
if you have idea what im DOING WRONG PRECISELY ;-) i will it realy…"
can some one help me with those issue pls ?arducopter 3.3.3 / pixhawkafter msg11.target_system=1; msg11.custom_mode=4; …
"so first vido from short test ;-) just take off and land, but for first test of tablet version WOD-GSC .... so im happy that nothing fired,exploded, crashed etc....
https://www.facebook.com/petr.zverina.56/videos/1314048708623358/"
https://www.facebook.com/petr.zverina.56/videos/1314048708623358/"
"WOD GSC working, touch control full integrated, so soon first test in air ;-)"
"hi all , we transport now WOD-GSC to Acer iconia tablet ( win 8 and win 10 )
so soon some videos from test software ;-)"
so soon some videos from test software ;-)"
"so STP ( software trim proces ) work realy well, today tested , configuration :
GSC :
Laptop TAROX with 2nd gen i7
GSC-WOD v 0.55a
433mhz 500mw telemetry
Spektrum dx6i
Drone : HEXEN Mk1
Pixhawk clone
6x 2212/920 motors ,…"
GSC :
Laptop TAROX with 2nd gen i7
GSC-WOD v 0.55a
433mhz 500mw telemetry
Spektrum dx6i
Drone : HEXEN Mk1
Pixhawk clone
6x 2212/920 motors ,…"
"i had same problem too ;-) so i made in my WOD-GSC new trim process ;-)
http://diydrones.com/forum/topics/wod-mavlink-ground-station?id=705..."
http://diydrones.com/forum/topics/wod-mavlink-ground-station?id=705..."
"i found something strange. Is realy imposible make TRIM PROCES with 6 channel controler :-) i know is posible conect chanel 6 to chanel 7, but no if you use spectrum satelite straight to pixhawk. or soem receiver with PPM output, then you dont have…"
"btw today was first time HEXEN mk1 in AIR ;-) with out setup, just basic, and he was fly stable and nothing exploded , fired off or crashed :D so all ok :D"
"i think i know what to do ;-) i made my gcode mixer, whits allow you print more filaments by one extruder. and i think adwantage will that wires can be part of plastik, so you reduce weight becouse electric part will also construction part ;-) so…"
