Not able to order the 900 MHz kit due to missing headers?

  • "Whoops! Our apologies, but although this product is listed as in stock, there is actually one component (6 Pin Right Angle Male Header) that we don't have in hand. Rather than ship an incomplete product, please try in a few days. We usually restock quickly."

Any ETA for this part? 

Views: 323

▶ Reply to This

Replies to This Discussion


3D RoboticsPermalink Reply by Chris Anderson on April 8, 2012 at 3:18pm

Just check back in a few days, like it says. 

Permalink Reply by John Moore on April 8, 2012 at 4:02pm

The reason I posted the question is because it seems strange to hold up orders because of a readily available part like pin headers and I thought it might be an error in the system.

Permalink Reply by Jeff Simpson on April 9, 2012 at 8:59am

It came back in stock for a few minutes. I ordered a kit, but now it says out of stock again (but the headers themselves say in-stock)

Permalink Reply by Zachary Eldridge on April 9, 2012 at 9:15am

Send mine my ways anyways please. I have plenty of headers.


ModeratorPermalink Reply by Mark Harrison on April 9, 2012 at 1:45pm

Back in stock. Oh no, now they're out of antennas!

This problem would be easily solved if you all would stop trying to order until my order is successfully placed!!!

Permalink Reply by Gabriel on April 9, 2012 at 5:51pm

every time i go ummm when it's in stock by the time i decide yes to buy it's out of stock....

Permalink Reply by Gabriel on April 11, 2012 at 12:25am

ok purchased this time !

Permalink Reply by Zachary Eldridge on April 13, 2012 at 5:55am

They most be still waiting on headers I had my ordered since last Friday. Still in Proccessing.

Permalink Reply by Gabriel on April 14, 2012 at 8:18pm

I'm not sure they are in production yet only people who have them are the developers at the moment from what i can see... hopefully someone will give us a ETA 


3D RoboticsPermalink Reply by Chris Anderson on April 14, 2012 at 8:56pm

A bunch went out last week. They should start shipping again next week. 

RSS

Social Networking

Top Content 

1 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
2 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
3 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
4 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
5 ArduCopter-3.0 ready for wider use

ArduCopter-3.0 ready for wider use
6 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
7 Drone shot down by police

Drone shot down by police
8 MAAT final version is being tested

MAAT final version is being tested
9 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe
10 Thirty Days (#28): McMaster-116 lift

Thirty Days (#28): McMaster-116 lift

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service