3D Printing Drone Parts

Information

3D Printing Drone Parts

A group for both those who are fortunate to be actively printing parts with their printers or online services, and those just interested.  

Location: Sol III (Earth)
Members: 218
Latest Activity: Jul 15

Discussion Forum

London 3d printing show recap

Started by James Wright. Last reply by Eli Cohen May 28. 1 Reply

Hello,I just wanted to share my experience at the London 3D printing show, I went because I'm looking into getting a new 3D printer. …Continue

DJI F550 / 450 Folding Landing gear legs

Started by Michael Ciurescu Apr 6. 0 Replies

Here is my F550 folding landing gear:http://www.thingiverse.com/thing:759368Please see the comments on the Thingiverse…Continue

Tags: F450

3D Printed Folding Quadcopter

Started by Michael Ciurescu. Last reply by Michael Ciurescu Apr 6. 6 Replies

Here is my 3D Printed…Continue

Tags: Quadcopter, Folding, Printed, 3D

Phone and telemetry radio holders

Started by barneyj Mar 22. 0 Replies

Holder for IRIS transmitter - http://www.thingiverse.com/thing:724526For JR9303 transmitter - …Continue

Comment Wall

Comment

You need to be a member of 3D Printing Drone Parts to add comments!

Comment by Eric on June 21, 2014 at 2:06pm
I've had good luck with MakeXYZ.com. Sort of like 3d hubs but better in my opinion.
Comment by Edwin WIdjonarko on June 21, 2014 at 1:58pm

Hi Bill,

Sorry for the late reply, but I'd like to add to Andrew's comment. I too had a good experience with 3D hubs. I printed a customized cam holder with bearings and all. You only need to provide the STL file. Warning: 3D hubs will "optimize" the fill rate of your model. It tends to make it lighter, but might compromise structural strength. I don't know if there's any setting for this.

Hope this help. Cheers, 

Comment by Andrew Neushul on June 20, 2014 at 10:06am
Hi Bill my email is aneushul@submerse.com. I'm located is Santa Barbara CA

Moderator
Comment by Bill Piedra on June 20, 2014 at 5:14am

@andrew , @joshua - Thanks.  I'm going to try both.  Andrew, can you send me an email or tweet direct.  Where are you located ? 

tweet me @billrockus

Comment by Andrew Neushul on June 18, 2014 at 2:13pm
I have 3d printed clamps for carbon fiber tubes. I just finished a design that converts a standard DJI 450 to use CF tubes instead of the plastic arms. I have a printer, would gladly print some parts for you as I'm interested in doing the same thing - covering the printed parts with CF
Comment by Joshua Johnson on June 18, 2014 at 12:35pm
@Bill,
Trying using the official 3D Printing Service of CADDrones.com which is 3DHubs.com! You should be able to find someone local using that.

Moderator
Comment by Bill Piedra on June 18, 2014 at 10:06am

I don't have a 3D Printer, but I would like to print some parts.  Rather than build a 3d printed fuselage, I am using carbon fiber tubes and plates.  What I would like to do is print the tube clamps and other hardware on a 3D printer and reinforce them with CF/Epoxy.  I have used Shapeways before, but I would really like to find someone local who can do the printing for me.  I need fast turn around which I don't get from Shapeways.  

Comment by Mike Bristol on March 28, 2013 at 12:58pm

Awesome!

Comment by Bradley J Carr on March 28, 2013 at 12:12pm

Just finished the build of my 3d Printer.  LETS SEE WHAT WE CAN DO!!!!!

Comment by Scott Walters on March 11, 2013 at 9:29pm

My Thingiverse.com Parts page.

I have some printable RC models here, http://www.thingiverse.com/scooter46290/designs/page:1

 

Members (218)

 
 
 

© 2015   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service