"Guys, what is the best prop for this plane? I'm using NTM35-36a-1400Kv motor and 60A ESC. Thanx!"
Yiangos Yiangou's Page
Latest Activity
espenthrondsen commented on Yiangos Yiangou's blog post Yet another Build log - Epp FPV"Did you fly this plane ? Do you have a parameter file to share ?"
Yiangos Yiangou commented on Kirill's blog post ArduCopter Quad Assembly and the first flight with camera on board"nice video kirill:) especially the building pics part :)"
Yiangos Yiangou replied to James masterman's discussion Powering ardupilot"the power consumption on of the APM and the servos is not that high. the supply is clean enough as ur using batteries , however u need to mesure how much flying time u can get out of the 1500 NiMH :)."
Yiangos Yiangou replied to James masterman's discussion Powering ardupilot"Well , i see the advantage of having slightly more flying time :) other than that i dnt see any other reason to do it."
T.D. Gonzales commented on Yiangos Yiangou's blog post Yet another Build log - Epp FPV Part 3"How is did it handle with 2 5000 mAh batteries in the nose? I'm just curious since I am looking at getting this plane."
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"Sure,
First thinks first, you need to cut the traces that connect the power pin to the rest of the board. You can see that on the pic that i posted. (+ve pin is the middle one) just use a paper cutter or smthing
there is also another trace u need to…"
Alex Lee commented on Yiangos Yiangou's blog post Yet another Build log - Epp FPV"thanks for the pics. I was looking for an easy solution to better affix the canopy and putting a rod straight through and just rubberbanding it is awesome.. thanks!"
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"Sure :)
First I cut the trace from the +ve pin (there are 2 traces, one which leads to the bottom pin and one on the other side of the pcb which leads to the smaller perpendicular pcb thouse are connected together probalby to withstand more current…"
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"
Here is a picture of my mod with an irf 4905 :)"
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"Russel i agree with simon, the first diagram was correct :) you need to change the mosfet in ur diagram , it should be a Nfet"
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"the forward diode voltage is -4V therefore at ~-11 volts the conductivity is near negligible "
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"IS this works because in order for drain and source to conduct the voltage at the gate must be grater than the gate threshold voltage. so in the correct polarity , in the gate you will have ~11v far grater than the threshold (-2v). When in reverse…"
Yiangos Yiangou commented on Russell B. Sutton's blog post Polarity Protection for Turnigy 9x Tx"Russell i just did a try with an IRF4905 and the 1st diagram worked, the 2nd was opposite (the way to burn it :P)"
Jimmy P. commented on Yiangos Yiangou's blog post Yet another Build log - Epp FPV"The batteries are in parallel. The motor is: AerodriveXp SK Series 35-36 1400Kv / 550w (the quality of this motor leaves nothing to be desired - it is very very good)
The ESC is the Turnigy Plush 60A"
Yiangos Yiangou commented on Yiangos Yiangou's blog post Yet another Build log - Epp FPV Part 3"Thank you kirill
Darren looks nice, I'll try it in a bit :)"
Profile Information
- About Me:
- High school student who loves electronics
- Tell us a bit about your UAV interest
- Started by a school project and am in love ever since
Yiangos Yiangou's Blog
Yet another Build log - Epp FPV Part 3
Posted on May 28, 2011 at 6:28am 6 Comments 3 Likes
First of all I installed some magnets on the wings (so they can be detachable)
Then i took out some foam and glued some Velcro to make space for my 2 5000mah batteries
…
Continue Yet another Build log - Epp FPV Part 2
Posted on May 5, 2011 at 3:09am 8 Comments 0 Likes
Electronics arrived today :)
Glued the back wing and shaped the foam for the rudder ( Is there any other way to mount the servo rather than gluing it to the foam?)
Installed the motor , which is a turnigy 35-42B 1250Kv, mount needs some hot glue…
Yet another Build log - Epp FPV
Posted on April 29, 2011 at 1:00pm 10 Comments 0 Likes
So my kit from HK arrived yesterday and I should note that this is my first build ( If you see terrible mistakes don't hesitate to shout;))
Soldered the carbon rod using some super glue. I installed those holders just in case even though most probably am gonna put the elevator end radder servos on…
ContinueComment Wall (1 comment)
- At 3:17pm on May 2, 2011,
Darren said… was out of town attending our semi annual state fishing tournament. i am a member of the staff and the webmaster for our state bass fishing club. www.iabass.com
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduPlane User Group
682 members
-
ArduCopter User Group
1289 members
-
Andropilot Users Group
182 members
-
Moderators
24 members
-
Telemetry over cellular …
248 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
