3+km HD FPV system using commodity hardware

Hi

Over the last couple of months I have been working on a project that might be of interest to you: https://befinitiv.wordpress.com/wifibroadcast-analog-like-transmission-of-live-video-data/

Basically it is a digital transmission of video data that mimics the (advantageous) properties of an analog link. Although I use cheap WIFI dongles this is not one of the many "I took a raspberry and transmitted my video over WIFI"-projects.

The difference is that I use the cards in injection mode. This allows to send and receive arbitrary WIFI packets. What advantages does this give?

- No association: A receiver always receives data as long as he is in range

- Unidirectional data flow: Normal WIFI uses acknowledgement frames and thus requires a two-way communication channel. Using my project gives the possibility to have an asymmetrical link (->different antenna types for RX and TX)

- Error tolerant: Normal WIFI throws away erroneous frames although they could have contained usable data. My project uses every data it gets.

For FPV usage this means:

- No stalling image feeds as with the other WIFI FPV projects

- No risk of disassociation (which equals to blindness)

- Graceful degradation of camera image instead of stalling (or worse: disassociation) when you are getting out of range

The project is still beta but already usable. On the TX and RX side you can use any linux machine you like. I use on both sides Raspberrys which works just fine. I also ported the whole stack to Android. If I have bystanders I just give them my tablet for joining the FPV fun :)

Using this system I was able to archive a range of 3km without any antenna tracking stuff. At that distance there was still enough power for some more km. But my line of sight was limited to 3km...

In the end, what does it cost? Not much. You just need:

2x Raspberry A+

2x 8€ wifi dongles

1x Raspberry camera

1x Some kind of cheap display

Happy to hear your thoughts/rebuild reports :)

See you,

befinitiv.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

        • Two way communication also wouldn't be very good, because it would cause collisions (=video dropouts) when the ground-station sends something at the same moment with the air-station. In this regard wifi works similarly to the "plain old ethernet without switches" (with coax cables or hubs).

          But I think it should be possible to set up two wifibroadcasts with two wifi cards on different wifi channels, one that sends stuff from the air-station to the ground-station and one that sends stuff from the ground-station to the air-station.

          If one would want to use only one wificard/channel for bi-directional communication, one would have to implement some kind of time division multiplexing, but that's far from being trivial.

    • Should be simple if you follow the latest post from Befinitiv: https://befinitiv.wordpress.com/2015/07/06/telemetry-osd-for-wifibr...

      Telemetry OSD for wifibroadcast
      This post shows how to add an overlay with telemetry information onto a video stream — Since the last flyaway of my quad having a telemetry link that…
  • Had some fun in the park today.  Camera wobble gone.  The lense I'm using doesn't do justice to the cause though and creates an unwanted blur.  Overall, I was very pleased with how well things improved with CP antennas.  Antennas are everything!

    www.youtube.com/watch?v=vXa4HRqKj1M

    :)

  • My latest concoction.  2 TX radios!  Wish me luck!! :)

    FSuZihM.jpg

    aOC0YIT.jpg

    • To our non euro counterparts, has anyone successfully ordered the CSL 300mbit wifi units? I've found some but they're 20 euro a pop and freight is 40 euros, so I'd be looking at 80 euros total just for the RX side of things. 

  • Did first test flight today. Worked pretty well when very close to the ground and within 15m's or so.

    The setup:

    Alien H4 Pixhawk with Frsky 2.4Ghz TX/RX

    Video TX WN722 w standard omni

    Video RX WN722 w standard omni

    Wifibroadcast setup Ch7

    Resolution: 1280x720

    FPS=48

    Bitrate=3,000,000

    Keyframerate=120

    Retransblocksize=8

    I was getting a lot of this happening when I went further than 15m's away:

    3702040843?profile=original

    I moved the antenna so it was pointing below the quad and that improved it slightly.

    What do the experts think? I'm thinking the antenna's need to be changed over to something different and do you think the TX/RX running at 2.4GHz will be adding to this. I've ordered a UHF Rx/Tx but haven't got it yet...

    Thoughts/comments welcome..

    Cheers

    • w9m6FfT.jpgThis is the antenna i'm using for the TX and RX side (on the left):

      It's a 2.4GHz biquad antenna.  Getting good results with it.  I'll be making a couple Circular Polarized versions next.

      DIY instructions here:

      youtube.com/watch?v=4t6OliwhJ5g

      • Cheers Maulkans - I'll fire up the soldering iron and make some! 

This reply was deleted.

Activity

DIY Robocars via Twitter
3 hours ago
DIY Robocars via Twitter
RT @SmallpixelCar: @a1k0n @diyrobocars I learned from this. This is my speed profile. Looks like I am too conservative on the right side of…
5 hours ago
DIY Robocars via Twitter
RT @a1k0n: @SmallpixelCar @diyrobocars Dot color is speed; brighter is faster. Yeah, it has less room to explore in the tighter part, and t…
5 hours ago
DIY Robocars via Twitter
RT @a1k0n: I'm gonna try to do proper offline reinforcement learning for @diyrobocars and throw away all my manual parameter tuning for the…
yesterday
DIY Robocars via Twitter
RT @circuitlaunch: DIY Robocars & Brazilian BBQ - Sat 10/1. Our track combines hairpin curves with an intersection for max danger. Take tha…
Thursday
DIY Robocars via Twitter
RT @SmallpixelCar: Had an great test today on @RAMS_RC_Club track. However the car starts to drift at 40mph. Some experts recommended to ch…
Sep 11
DIY Robocars via Twitter
RT @gclue_akira: 世界最速 チームtamiyaのaiカー https://t.co/1Qq2zOeftG
Sep 10
DIY Robocars via Twitter
RT @DanielChiaJH: Always a good time working on my @diyrobocars car at @circuitlaunch. Still got some work to do if I’m to beat @a1k0n howe…
Sep 10
DIY Robocars via Twitter
RT @SmallpixelCar: My new speed profile for @RAMS_RC_Club track https://t.co/RtLb7TcgIJ
Sep 10
DIY Robocars via Twitter
RT @SmallpixelCar: Practiced at @RAMS_RC_Club today with my new @ARRMARC car https://t.co/AEu2hCx89T
Aug 28
DIY Robocars via Twitter
Aug 24
DIY Robocars via Twitter
RT @gclue_akira: 柏の葉で走行させてるjetracerの中身 #instantNeRF #jetracer https://t.co/giVvuE4hP7
Jul 4
DIY Robocars via Twitter
Cool web-based self-driving simulator. Click save when the AI does the right thing https://github.com/pncsoares/self-driving-car
Jul 4
DIY Robocars via Twitter
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
Jun 25
DIY Robocars via Twitter
Jun 25
DIY Robocars via Twitter
Jun 16
More…