Discussions

3dr links only works with usb

Posted by Andi on May 23, 2014 at 12:37pm

Hi Folks,

after i dig out my copter for about one year of absence the first i did was updating it to the new arducopter firmware. However, everthing works fine while connected via usb.

then i unplugged usb, put my 3dr radio into the pc and powered the copter with its lipo and... the 2 radios didn't found each other. Well i thought of some msiconfigration. I unplugged the lipo from the copter and put the usb cable back in... well the 2 radios found each other immediatly.

so in short... if the copter is powered with usb the 2 radios connected immediatly. if the copter is powered standalone with lipo and usb disconnected they keep green blinking... i have absolutly no clue how this can be.

i'm thankful for all tipps you maybe want to share with me about this problem. i have no clue what to do now.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –
Follow

Replies

  • Marcin Krawczyk May 25, 2014 at 5:36am

    I mean printscreen from MP or 3DR Radio config tool, with config loaded from both radios simultaneously...

    There we can't see FW version, if both radios has same settings etc.

    • Andi > Marcin Krawczyk May 25, 2014 at 7:02am

      this is mainly the config of both. As i said, if connected via usb they both find each other, so i'm pretty sure it's not a settings issue, maybe you can tell me what you are looking for.

      • Marcin Krawczyk > Andi May 25, 2014 at 9:19am

        I'm looking for differences between units, difference in FW versions etc.

        Can you post pictures of your config while "the copter is powered with usb the 2 radios connected" and "copter is powered standalone with lipo and usb disconnected". I can't clearly understand this states...

        For propper work it's enough, if both units have stable +5V power, nothing more....

        • Andi > Marcin Krawczyk May 25, 2014 at 10:24am

          Well it's simple. if the copter is powered with lipo my ground radio is not going to connect, it keeps green blinking.

          But if i disconnect the lipo from the apm and connect the APM via USB to the PC too, both connect immediatly and stop blinking.

          • Marcin Krawczyk > Andi May 25, 2014 at 10:30am

            Disconnect APM from everything except 3DR radio and power it with simple BEC, connected to INPUT servo rail. Measure Vcc on telemetry port. Check, if it works.

            • Andi > Marcin Krawczyk May 25, 2014 at 11:00am

              thanks for the suggestion but i do not connect the apm via BEC:

              however to disconnect the radio i have to disassemble the whole copter, this is a lot more complicated than it should be. well will do it in the next few days. I hoped their might be something i can do in the settings without changing something on the hardware.

  • Marcin Krawczyk May 24, 2014 at 12:44am
    Show config of your radios.
    • Andi > Marcin Krawczyk May 24, 2014 at 2:22am

      sure...

      S0: FORMAT=25

      S1: SERIAL_SPEED=57

      S2: AIR_SPEED=32

      S3: NETID=25

      S4: TXPOWER=8

      S5: ECC=1

      S6: MAVLINK=1

      S7: OPPRESEND=1

      S8: MIN_FREQ=433050

      S9: MAX_FREQ=434700

      S10: NUM_CHANNELS=10

      S11: DUTY_CYCLE=20

      S12: LBT_RSSI=0

      S13: MANCHESTER=0

      S14: RTSCTS=0

This reply was deleted.

Activity

Neville Rodrigues liked Neville Rodrigues's profile
Jun 30
Santiago Perez liked Santiago Perez's profile
Jun 21
More…