450Quad crashed in stabilize mode!!!

Hay guys....

                I was flying a 450quad with pixhawk3.3.3with vibration dampers, M8n gps, 3DR telemetry, BEC module and futaba transmitter. I had a clean fight in stabilize mode for about 3mins and then quad suddenly yawed in counter clockwise direction for 3 times and fell into the ground.... from dataflash log, it showed EKF error... but I dont know what caused that error.... all the esc and motors are working fine. I dont think that prop could be damaged  or any other mechanical issues during flight... I am attaching the log file below... pls someone could analyse and tell what could caused crash....

2017-02-21 16-55-13.bin

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Hay  Mossbackfarm... I checked all the motors and escs. All are fine... I use vibration isolation for mounting the pixhawk. I even flew the same quad about five times before the crash (sixth flight crashed)

  • Hay  Michael Burmeister thanks for the reply.... I have attached the correct file... I could plot motor outputs (RCOUT)... I will also attach .log file 

    "I think it is possible to crash in Stabilize mode with version 3.3.3 do to over use of the GPS in this mode" - Stabilize mode does not use gps inputs. can you explain me more clearly?

    2017-02-21 16-55-13.log

  • At 3:28:30, yaw starts picking up right after your vibrations start to spike after being good for the previous portions.  Check motor / esc?

  • This log shows a normal flight with no issues.  RCOUT is not logged which is needed when determining an issue with flight.

    I think it is possible to crash in Stabilize mode with version 3.3.3 do to over use of the GPS in this mode.  Later version I believe corrected this issue.

    This log did not show any of this and did not show any Yaw issues so I don't think this is the correct log.

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @a1k0n: @DanielChiaJH @diyrobocars @circuitlaunch Here's my car's view of that race. About 8.4 second lap times for laps 2 and 3... both…
yesterday
DIY Robocars via Twitter
RT @DanielChiaJH: Great racing against @a1k0n today at @diyrobocars! Pretty cool to both break sun-9s at the track today I think I got very…
Sunday
DIY Robocars via Twitter
Broadcasting the @circuitlaunch race live now at https://m.twitch.tv/diyrobocars Races begin around 2:00pm PT
Saturday
DIY Robocars via Twitter
RT @a1k0n: ran a huge number of hyperparameter tuning experiments yesterday; now I can train a new policy, far with better quality, in 15 m…
Saturday
DIY Robocars via Twitter
RT @a1k0n: Did I get rid of hand-tuned parameters? Yes. Am I still hand-tuning more parameters? Also yes. I have a few knobs to address the…
Sep 26
DIY Robocars via Twitter
RT @a1k0n: I'm not going to spoil it, but (after charging the battery) this works way better than it has any right to. The car is now faste…
Sep 26
DIY Robocars via Twitter
RT @a1k0n: Decided to just see what happens if I run the sim-trained neural net on the car, with some safety rails around max throttle slew…
Sep 26
DIY Robocars via Twitter
Sep 24
DIY Robocars via Twitter
RT @SmallpixelCar: @a1k0n @diyrobocars I learned from this. This is my speed profile. Looks like I am too conservative on the right side of…
Sep 24
DIY Robocars via Twitter
RT @a1k0n: @SmallpixelCar @diyrobocars Dot color is speed; brighter is faster. Yeah, it has less room to explore in the tighter part, and t…
Sep 24
DIY Robocars via Twitter
RT @a1k0n: I'm gonna try to do proper offline reinforcement learning for @diyrobocars and throw away all my manual parameter tuning for the…
Sep 23
DIY Robocars via Twitter
RT @circuitlaunch: DIY Robocars & Brazilian BBQ - Sat 10/1. Our track combines hairpin curves with an intersection for max danger. Take tha…
Sep 22
DIY Robocars via Twitter
RT @SmallpixelCar: Had an great test today on @RAMS_RC_Club track. However the car starts to drift at 40mph. Some experts recommended to ch…
Sep 11
DIY Robocars via Twitter
RT @gclue_akira: 世界最速 チームtamiyaのaiカー https://t.co/1Qq2zOeftG
Sep 10
DIY Robocars via Twitter
RT @DanielChiaJH: Always a good time working on my @diyrobocars car at @circuitlaunch. Still got some work to do if I’m to beat @a1k0n howe…
Sep 10
DIY Robocars via Twitter
RT @SmallpixelCar: My new speed profile for @RAMS_RC_Club track https://t.co/RtLb7TcgIJ
Sep 10
More…