Developer

APM:Plane 2.74 released

The APM dev team is delighted to announce the release of APM:Plane 2.74, a major new release with a lot of new features. This release is recommended for anyone flying fixed wing aircraft with an APM2 or PX4.

There are a lot of changes in this release, but some of the highlights are:

  • new APM_Control attitude controllers.
  • new TECS speed/height controller from Paul Riseborough.
  • two new flight modes, ACRO and CRUISE
  • new camera trigger by distance system, for better aerial mapping
  • dozens of small fixes and improvements from two months of development
  • lots more documentation, including tuning guides for all the new parameters

Scroll down for a more complete list of changes, but before that I'd like to give you a bit more detail on the highlights above.

New Attitude Controllers

The new "APM_Control" attitude controllers have been in development for a long time. Originally developed by Jon Challinger last year, they were extended by Paul Riseborough and made compatible with the existing parameter names. The key advantage of these new controllers is their improved handling of noise, and much better ability to tune for your aircraft. There is a new tuning guide in the wiki which gives detailed instructions on how to make the most of the new capabilities.

One of the big effects you will see with the new attitude controllers is better handling of pitch compensation in turns. The new PTCH2SRV_RLL parameter makes tuning for flat turns much easier, which has been a major source of frustration in the past.

The new controllers also handle sensor noise much better, especially if you use any D term in your roll or pitch controllers.

New Speed/Height Controller

The new TECS speed/height controller is the second major controller change in this release, and will make a world of difference for aircraft with an airspeed sensor. After a lot of testing I decided to make TECS the default in this release, although you can switch back to the old controllers using the ALT_CTRL_ALG parameter if need be. If for some reason you find you do need these old controllers then please let me know, as I am planning on removing the old controllers in the next release.

The previous airspeed controller for speed/height suffered from a major problem that it gave absolute priority to airspeed. If the aircraft could not achieve the target airspeed you had set then it would dive to gain speed, even to the point of diving into the ground. This made it quite fragile, and you had to be very sure of your airspeed configuration.

The new controller operates over a range of airspeed values, set using the ARSPD_FBW_MIN and ARSPD_FBW_MAX parameters. That controller will try to meet both the airspeed and altitude demands of the mission, but if it can't reach the target speed it will happily fly a bit slower, as long as it doesn't get below ARSPD_FBW_MIN. You can control the relative priorities of speed versus height using the TECS_SPDWEIGHT parameter. See the full tuning guide for details.

New ACRO flight mode

After a suggestion from Thomas in the 2.73 release thread, we have added a new ACRO flight mode.

This modes brings rate controlled stabilization to APM:Plane, and should help give you an "on rails" manual flight experience. It is a lot of fun to fly, but it is not for beginners!

We're planning on expanding the ACRO mode in future releases. Right now it is great for "locked in" flying, and also good for loops and handles inverted flight very nicely. It doesn't yet handle knife-edge or prop-hanging.

New CRUISE flight mode

After a suggestion from Hein, we now have a new CRUISE flight mode. This mode is ideal for longer distance flying without a pre-programmed mission. It is like FBWB, but also does ground track heading hold, with heading update via aileron or rudder.

I've been testing CRUISE at my local flying field, and it is the easiest mode to fly in APM. Just steer the plane around the sky, and when you stop steering it locks onto a ground track and holds it. It isn't a good mode for takeoff and landing, but once you are in the air it is great.

New camera trigger system

When using APM for aerial mapping where you want photos taken at regular distances, the previous system was to setup a grid mission with a "camera trigger" mission item at regular intervals within the mission. That worked, but led to overly large and complex missions. You can now just set a single parameter CAM_TRIGG_DIST to the number of meters of flight between photos, and the APM will take care of when to trigger the camera. This makes for much simpler missions, and also works in other flight modes, including FBWB and CRUISE.

Lots of smaller changes

As is usual with a new release after a couple of months of development there were a lot of smaller improvements based on feedback from users. Many thanks to everyone who gave feedback and contributed patches!

Here is a partial list of the changes:

  • added new GND_ALT_OFFSET parameter for ground station barometric correction
  • made it possible to set the failsafe battery voltage and battery level at runtime via parameters
  • added MIXING_GAIN parameter for controlling the elevon and v-tail mixers
  • fixed stick mixing range in AUTO modes  (thanks Soren!)
  • fixed mode logging in dataflash
  • added support for the EagleTree I2C airspeed sensor on PX4
  • added new RCMAP_* parameters for re-mapping control channels (good for DSM and SBUS receivers on PX4)
  • made it possible to configure board orientation at runtime, to make setup easier without rebooting
  • switched to new task scheduler for more accurate internal timing
  • added a new RELAY_PIN parameter for setting up camera trigger via a digital pin
  • added secondary rudder support, useful for when a separate servo is used for a nosewheel and the rudder, or for v-tail planes with nosewheels
  • fixed RTL glide slope when starting above the target RTL altitude. Descent should now be smooth over long distances. Many thanks to Kitsen13 for raising this.
  • fixed a bug with FBWB airspeed control. Many thanks to Gabor for reporting this
  • Added FS_LONG_TIMEOUT and FS_SHORT_TIMEOUT parameters. Many thanks for the suggestion by Aleck
  • fixed handling of deadzone parameters on RC channels. Many thanks to Soren for reporting this
  • many small C++ fixes from NeuroCopter. This sort of detailed review of our code is much appreciated!
  • fixed analog in handling with some unusual devices - thanks to Andi for noticing this!
  • added support for apparent versus true airspeed calculations based on pressure altitude, for better flight control at higher altitudes
  • avoid writing unchanged bytes to EEPROM, for faster updates and less wear on the chip
  • cope better with large yaw changes in the AHRS code
  • improved the reliability of USB connections on PX4
  • added PX4 support for RELAY (thanks to Marco Bauer)
  • fixed handling of high spin rates in AHRS (thanks Jurgen!)
  • removed support for the old APM1 1280 based boards.

This new release has a lot of new features that should improve the flying experience for all APM users. The APM dev teams wishes all APM users many enjoyable flights, and we hope you have as much fun flying this release as we had making it.

Happy flying!

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Mission Planned HUD said: Bad Compass Health.

    This happens on air, from time to time.

    What is the reason for this error?

    Is it safe to try flying in Auto?

    APM2.5, internal compass, MediaTek GPS, No Airspeed sensor

    3692853181?profile=original

  • Hi, I posted a thread in the main forum asking about ACRO mode.

    I need a mode that's lighter than ACRO, which basically means disabling the 'attitude locking' in ACRO.

    The docs on plane.ardupilot.com site mention an 'ACRO_LOCKING' param, but I can't see it in mission planner.

    In fact, it doesn't even show up in the main repo (looks like it only exists on tridge's fork).

    Can anyone provide some feedback/assistance with this? I really need to disable attitude locking & all the extra junk that might be piled onto ACRO (I just want a simple, *real* gyro rate-based PID controller 'flight stabilization', w/ no bells&whistles).

  • Hello,

    I've posted this content on Ardupilot.com's forum but sill haven't got answer. It looks that less people visits that forum than this forum, so I post it here again.
    I'm testing Arduplane 2.74b with Mission Planner 1.2.80. When I tried to set up WP_LOITER_RAD in Mission Planner CONFIG/TUNING Full Parameter List to -80 to have anti-clockwise loiter, it was accepted. Then I changed to FLIGHT PLAN, -80 was displayed in Loiter Radius. After editing flight plan I pressed Write WPs. But when I have a look at CONFIG/TUNING Full Parameter List, WP_LOITER_RAD has changed to 176. I tried with different values like -100, -300, and after Write WPs they have changed to 156 or 212. It looks like the negative values always changed back to values between 0..255 but keeps the relation that 80+176=256, 100+156=256, 300+212=512, so I can conclude that there may be a mistake in declaration of uint8. BTW on the field the loiter direction is always clockwise even when I have changed back in Full Parameter List to -80 after Flight Plan Write WPs. Does any one know the reason?

  • Any idea when we might expect the next version for general use?

     

  • Hello!

    Tested today 2.75beta2, works perfect! Mysteries with data-link 433mhz resolved, probably cable went out from a connector, when landed, now it is ok. Even roll/pitch in FBW resolved, roll in apm was not reversed :) and simply it was all wrong. But now, as in video-game goes fpv :)

    Just a question: I put RTL alt 30k cm, but when is on higher altitude, it descends to 30m. WHy is it not simply as on multirotors, when on higher altitude then in mnimal, it remains on that altitude, and loiters when is back to home.

    Anyway, is there any known bug for this beta2, as I will only test basic flight modes, but might try something further... ?

  • Moderator

    Is the v2.74b HIL simulation working for everyone? I can't get the APM to control the plane in either X-Plane or Flightgear.

  • Hello!

    I dont get it, are the gains still too low? FBW and Cruise are ok, but Loit and RTL are not doing well, the plane starts to climb and tries to get rolled too much, afterwards it heads nose down in a spirale, rapidly loosing height. In manual, everything is ok. Please help!

    Thanks in advance

    2013-10-05 15-36-39.tlog

  • Tridge, Paul, or some other expert,
    Could you please help us unravel this little mystery?
    http://diydrones.com/forum/topics/plane-i-programmed-1-loiter-turn-...

    We dont understand why there were 4 loiter turns rather than one? Is this a bug or our ignorance?
  • Hi, can anyone tell me if COMPASS_MOT_X (and Y and Z) work in Arduplane v2.74b?
    Also the description of COMPASS_MOTCT says "Do not change manually" How are you supposed to set it?


    Secondly,in a reply  Nathaniel Caner says:- "In my experience in a plane (as opposed to a multi-copter) the compass

    is more trouble than it;s worth unless you have poor GPS reception"

    Nathaniel,do you suggest setting COMPASS_USE to Zero i.e  "disable the use of the compass (instead of the GPS) for

    determining heading"? Does the plane still track OK, especially in windy weather?

    Thanks David


     

  • Had an interesting problem today.  The guys were flying an F2 with an APM 2.5 running 2.74b.  First flight went fine but on the second flight the plane rolled inverted and they weren't able to recover before a minor crash (repairable.)  Not sure why it rolled over but my real question is: what could keep the APM from recording a log file?  Went to play the log file from the accident flight and there isn't one.  I think the two problems might be related.


    Thanks,

    Jimmy

This reply was deleted.

Activity