Warning #1: an issue has been found with Tower's Pause button which can cause the vehicle to fly to an old position if the vehicle has not sent a position update to Tower in some time.
Warning #2: Copter-3.3.2 fixes a bug found in Copter-3.3.1's desired climb rate initialisation which could lead to a sudden momentary drop when switching from Stabilize or Acro to AltHold, Loiter or PosHold.
Warning #3: Copter-3.3.2 fixes an issue found in Copter-3.3.1 which could lead to hard landings in RTL or AUTO if the WPNAV_SPEED_DN was set too high (i.e. >400 or 4m/s) and/or the WPNAV_ACCEL_Z was set too low (i.e. <100 or 1m/s/s).
Warning #4: a bug was found in Copter-3.3 which could cause a sudden crash if you abort a Take-off initiated from a ground station. Video description is here. The bug is fixed in Copter-3.3.1 so we recommend upgrading.
Note #1: AC3.3-rc8 corrected a long standing bug in the HDOP reporting. HDOP values will appear about 40% lower than previously but this does not actually mean the GPS position is better than before.
Note #2: if upgrading from AC3.2.1 the vehicle's accelerometer calibration needs to be done again.
Note #3: set SERIAL2_PROTOCOL to "3" and reboot the board to enable FrSky telemetry like in previous versions.
Note #4: the wiki will be updated over the next few weeks to explain how to use the new features
Copter-3.3.1 is available through the mission planner. The full list of changes vs AC3.2.1 can be see in the ReleaseNotes and below are the most recent changes since AC3.3.
Sadly this version (and all future versions) will not run on the APM2.x boards due to CPU speed, flash and RAM restrictions.
Changes from 3.3:
1) Bug fix to prevent potential crash if Follow-Me is used after an aborted takeoff
2) compiler upgraded to 4.9.3 (runs slightly faster than 4.7.2 which was used previously)
Changes from 3.3-rc11:
1) EKF recovers from pre-arm "Compass variance" failure if compasses are consistent
Changes from 3.3-rc10:
1) PreArm "Need 3D Fix" message replaced with detailed reason from EKF
Changes from 3.3-rc9
1) EKF improvements:
a) simpler optical flow takeoff check
2) Bug Fixes/Minor enhancements:
a) fix INS3_USE parameter eeprom location
b) fix SToRM32 serial protocol driver to work with recent versions
c) increase motor pwm->thrust conversion (aka MOT_THST_EXPO) to 0.65 (was 0.50)
d) Firmware version sent to GCS in AUTOPILOT_VERSION message
a) pre-arm check of compass variance if arming in Loiter, PosHold, Guided
b) always check GPS before arming in Loiter (previously could be disabled if ARMING_CHECK=0)
c) sanity check locations received from GCS for follow-me, do-set-home, do-set-ROI
d) fix optical flow failsafe (was not always triggering LAND when optical flow failed)
e) failsafe RTL vs LAND decision based on hardcoded 5m from home check (previously used WPNAV_RADIUS parameter)
Thanks for your testing!
Acc is well calibrated. Compass I'm pretty sure is, I tried a few different times and flew some test flights and this last one had the lowest IMX, IMY and IMZ in ekf3. The only motor I'm 100% sure is not fake is #3 (they're sunnysky's), and pretty sure at least 1 or two are fakes. Which might be where the vibrations are from. Would it flying well in stabilize rule out vibes though?
is there a reason why you changed GPS_NAVFILTER to 3? It should remain at the default 8 for Airborne 4G.
You also changed EKF_VEL_GATE to 12 (default is 3). These are standard deviations, so you disabled the gate.
Perhaps you should try a complete reset of your Parameters.
Thanks Hubertus for your reply,
Did a reset of the parameters, recalibrated acc and compass, but loiter is still taking off horizontally.
Here's a log of the same craft taken last year with an older firmware and loiter worked well. Maybe my larger MR isn't adjusting well to a new parameter or change in the code?
Compass orientation looks OK.
Do you have a log with the reset parameters?
Hi attached is log with reset parameters. I see the position innovations (IPN and IPE) go bad around the time I bail out of loiter. Little strange as it seemed out of control during loiter but it shows a low IPN/IPE. Then IPN/IPE goes bad (but is flying OK in stabilize)
Nothing strange in the log except the failing Loiter.
MR tries to correct position, but flies in the wrong direction.
The GPS quality (NSAT/HDOP) is not as it should be with a M8N. Only 9 Sats all the Time.
Perhaps you can try to configure GPS.
Thanks guys for the help on this.
Any website with a listing of the meanings behind the ublox uncenter parameters? I successfully connect to uncenter on this gps but I remember trying to upload that config file to a m8n gps last year and it bricked it and ended up buying a new one (current one). Still have the old gps but it didn't seem to respond after uploading the file.
Sounds like it either has the wrong antenna installed or it is only reading the GPS sats and not GPS+Glonass
But yah other than that the logs look pretty good. Vibs are decent. Voltage is decent.
After verifying that the ground station or aircraft compass matched a real compass in all four directions, east and west were also reverse, the machine flew correctly in loiter.
I felt really dumb when I realized it.
You might be on to something. I did switch GPS units on the offseason. Its this gps http://www.readytoflyquads.com/mini-ublox-m8n-gps-w-35x35mm-mountin...
I have it mounted as shown (with the ceramic antenna up). Wires going towards the back of the MR. I recall someone saying not to do the roll180 setting as the orientation changed from the old apm days, and all new gps were actually upside down but that was considered right side up. Or has that been my problem, not putting the rotation_roll_180 in the drag down menu?